Re: Memory Issues
Stock.....ya know funny you mentioned that. I was playing in my bios and set the fan and temp alerts to on......immediately when i rebooted the alarms were going on.......not good huh?
What fan would you recommend for my set up. I bought Zalmans before on other boards and hate having to try an mod one to fit...I am not good at that. I need a good one that "just fits!".
Motherboard: Model:GIGABYTE GA-EP45-UD3R LGA 775 Intel P45 Rev#: 1.1 Bios Version:2.4
Cpu: Intel Core 2 Duo E8400 Wolfdale 3.0GHz 6MB L2 Cache LGA 775 65W Dual-Core
Ram: Corsair Dominator 1066 PC 8500 http://www.newegg.com/Product/Produc...82E16820145214
Power Supply Unit: Cool Max 600W
Default settings for new setups that are not overclocked.
note: replace all ?? with the value displayed in your bios.
----> Replace "Auto" with manually set values.
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster -------------- : [Auto] <--- FAST is OK
CPU Clock Ratio ---------------------- : [9x]
Fine CPU Clock Ratio ----------------- : [0.0] < ignore if not available
CPU Frequency ---------------------: 3.0ghz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control --------------- : [Enabled]
CPU Host Frequency (Mhz) --------------: [333]
PCI Express Frequency (Mhz) ---------- : [100] <--- Set to 100, never leave this on Auto
C.I.A.2 ------------------------------ : [Disabled]
Advanced Clock Control ------- [Press Enter]
CPU Clock Drive ---------------------- : <<< 800
PCI Express Clock Drive -------------- : <<< 900
CPU Clock Skew (ps) ------------------ : <<< 0
MCH Clock Skew (ps) ------------------ : <<< 0
DRAM Performance Control
Performance Enhance ------------------- : [Standard----no Disable option] <--- set to DISABLED when overclocking
Extreme Memory Profile --- (X.M.P.) --- : [Disabled] <--- Leave this Disabled
(G)MCH Frequency Latch ---------------- : [Auto]
System Memory Multiplier -------------- : [Auto]
Memory Frequency (Mhz) ---------------- : [Auto]
DRAM Timing Selectable ---------------- : [Auto] <-- set to MANUAL for overclocking
Standard Timing Control
CAS Latency Time -------- ?? ---------- : [Auto]
tRCD ------------------- ?? ---------- : [Auto]
tRP --------------------- ?? ---------- : [Auto]
tRAS ------------------- ?? ---------- : [Auto]
Advanced Timing Control
tRRD ------------------- ?? ---------- : [Auto]
tWTR ------------------- ?? ---------- : [Auto]
tWR --------------------- ?? ---------- : [Auto]
tRFC ------------------- ?? ---------- : [Auto]
tRTP ------------------- ?? ---------- : [Auto]
Command Rate (CMD) -------------------- : [Auto] <--- Auto or 0 is OK
Driving Strength Profiles
Driving Strength --------- : Press Enter <--- press ENTER to modify memory sub-timings when overclocking
Channel A
Static tRead Value --------------------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Channel B
Static tRead Value --------------------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Motherboard Voltage Control
CPU
Voltage Types------------ Normal -------- Current -----
Load-Line Calibration ----------------- : [Disabled]
CPU Vcore --------------- 1.22500 ---- : [Auto] <--- set to the 1.????? value
CPU Termination --------- 1.200V* ----- : [Auto] <--- set to the value to the left (Auto over-volts this too much when overclocking) Auto is OK if not overclocking
CPU PLL ----------------- 1.500V* ----- : [Auto] <--- set to the value to the left (Auto over-volts this too much when overclocking) Auto is OK if not overclocking
CPU Reference ----------- 0.760V* ----- : [Auto] <--- Auto Will set this correctly
CPU Reference2 ---------- 0.800V* ----- : [Auto] <--- Auto Will set this correctly
MCH/ICH
MCH Core ---------------- 1.100V ------- : [Auto] <--- set to 1.20 for 2x2GB ram (1.24 - 1.26, or 1.05 might be needed)
MCH Reference ----------- 0.760V ------- : [Auto]
MCH/DRAM Ref ------------ 0.900V ------ : [Auto]
ICH I/O ----------------- 1.500V ------- : [Auto] <--- set to the value to the left
ICH Core ---------------- 1.100V ------- : [Auto] <--- set to the value to the left
DRAM
DRAM Voltage ------------ 1.800V ------- : [Auto] <--- set to the max rated ram voltage (for most memory)
DRAM Termination -------- 0.900V ------- : [Auto]
Channel A Reference ----- 0.900V ------- : [Auto]
Channel B Reference ----- 0.900V ------- : [Auto]
Advanced Settings
Limit CPUID Max. to 3 ------------------ : [Disabled]
No-Execute Memory Protect -------------- : [Enabled]
CPU Enhanced Halt (C1E) ---------------- : [Disabled]
C2/C2E State Support ------------------- : [Disabled]
x C4/C4E State Support ----------------- : [Disabled]
CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
CPU EIST Function --------------------- : [Disabled]
Virtualization Technology -------------- : [Disabled] <--- Enabled if you use Vmware/Virtual PC
Integrated Peripherals
Legacy USB Storage Detect ------------- : [Enabled] <--- se
Originally posted by Chike
View Post
What fan would you recommend for my set up. I bought Zalmans before on other boards and hate having to try an mod one to fit...I am not good at that. I need a good one that "just fits!".
Motherboard: Model:GIGABYTE GA-EP45-UD3R LGA 775 Intel P45 Rev#: 1.1 Bios Version:2.4
Cpu: Intel Core 2 Duo E8400 Wolfdale 3.0GHz 6MB L2 Cache LGA 775 65W Dual-Core
Ram: Corsair Dominator 1066 PC 8500 http://www.newegg.com/Product/Produc...82E16820145214
Power Supply Unit: Cool Max 600W
Default settings for new setups that are not overclocked.
note: replace all ?? with the value displayed in your bios.
----> Replace "Auto" with manually set values.
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster -------------- : [Auto] <--- FAST is OK
CPU Clock Ratio ---------------------- : [9x]
Fine CPU Clock Ratio ----------------- : [0.0] < ignore if not available
CPU Frequency ---------------------: 3.0ghz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control --------------- : [Enabled]
CPU Host Frequency (Mhz) --------------: [333]
PCI Express Frequency (Mhz) ---------- : [100] <--- Set to 100, never leave this on Auto
C.I.A.2 ------------------------------ : [Disabled]
Advanced Clock Control ------- [Press Enter]
CPU Clock Drive ---------------------- : <<< 800
PCI Express Clock Drive -------------- : <<< 900
CPU Clock Skew (ps) ------------------ : <<< 0
MCH Clock Skew (ps) ------------------ : <<< 0
DRAM Performance Control
Performance Enhance ------------------- : [Standard----no Disable option] <--- set to DISABLED when overclocking
Extreme Memory Profile --- (X.M.P.) --- : [Disabled] <--- Leave this Disabled
(G)MCH Frequency Latch ---------------- : [Auto]
System Memory Multiplier -------------- : [Auto]
Memory Frequency (Mhz) ---------------- : [Auto]
DRAM Timing Selectable ---------------- : [Auto] <-- set to MANUAL for overclocking
Standard Timing Control
CAS Latency Time -------- ?? ---------- : [Auto]
tRCD ------------------- ?? ---------- : [Auto]
tRP --------------------- ?? ---------- : [Auto]
tRAS ------------------- ?? ---------- : [Auto]
Advanced Timing Control
tRRD ------------------- ?? ---------- : [Auto]
tWTR ------------------- ?? ---------- : [Auto]
tWR --------------------- ?? ---------- : [Auto]
tRFC ------------------- ?? ---------- : [Auto]
tRTP ------------------- ?? ---------- : [Auto]
Command Rate (CMD) -------------------- : [Auto] <--- Auto or 0 is OK
Driving Strength Profiles
Driving Strength --------- : Press Enter <--- press ENTER to modify memory sub-timings when overclocking
Channel A
Static tRead Value --------------------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Channel B
Static tRead Value --------------------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Motherboard Voltage Control
CPU
Voltage Types------------ Normal -------- Current -----
Load-Line Calibration ----------------- : [Disabled]
CPU Vcore --------------- 1.22500 ---- : [Auto] <--- set to the 1.????? value
CPU Termination --------- 1.200V* ----- : [Auto] <--- set to the value to the left (Auto over-volts this too much when overclocking) Auto is OK if not overclocking
CPU PLL ----------------- 1.500V* ----- : [Auto] <--- set to the value to the left (Auto over-volts this too much when overclocking) Auto is OK if not overclocking
CPU Reference ----------- 0.760V* ----- : [Auto] <--- Auto Will set this correctly
CPU Reference2 ---------- 0.800V* ----- : [Auto] <--- Auto Will set this correctly
MCH/ICH
MCH Core ---------------- 1.100V ------- : [Auto] <--- set to 1.20 for 2x2GB ram (1.24 - 1.26, or 1.05 might be needed)
MCH Reference ----------- 0.760V ------- : [Auto]
MCH/DRAM Ref ------------ 0.900V ------ : [Auto]
ICH I/O ----------------- 1.500V ------- : [Auto] <--- set to the value to the left
ICH Core ---------------- 1.100V ------- : [Auto] <--- set to the value to the left
DRAM
DRAM Voltage ------------ 1.800V ------- : [Auto] <--- set to the max rated ram voltage (for most memory)
DRAM Termination -------- 0.900V ------- : [Auto]
Channel A Reference ----- 0.900V ------- : [Auto]
Channel B Reference ----- 0.900V ------- : [Auto]
Advanced Settings
Limit CPUID Max. to 3 ------------------ : [Disabled]
No-Execute Memory Protect -------------- : [Enabled]
CPU Enhanced Halt (C1E) ---------------- : [Disabled]
C2/C2E State Support ------------------- : [Disabled]
x C4/C4E State Support ----------------- : [Disabled]
CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
CPU EIST Function --------------------- : [Disabled]
Virtualization Technology -------------- : [Disabled] <--- Enabled if you use Vmware/Virtual PC
Integrated Peripherals
Legacy USB Storage Detect ------------- : [Enabled] <--- se
Comment