Announcement

Collapse
No announcement yet.

i7 gigabyte ud5 - oc settings - help

Collapse
X
Collapse
 
  • Page of 2
  • Filter
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • #1

    i7 gigabyte ud5 - oc settings - help

    ok,
    here is my bios settings



    intel i7 920
    gigabyte x58 ud5
    patriot viper 1600ll (8-8-8-24 1600)


    Advanced CPU Features:
    CPU Clock Ratio ................................ [20x]
    Intel(R) Turbo Boost Tech .................. [Enabled]
    CPU Cores Enabled ............................ [All]
    CPU Multi Threading .......................... [Enabled]
    CPU Enhanced Halt (C1E) ................... [Enabled]
    C3/C6/C7 State Support .................... [Enabled]
    CPU Thermal Monitor ......................... [Enabled]
    CPU EIST Function ............................ [Enabled]
    Virtualization Technology ................... [Enabled]
    Bi-Directional PROCHOT ..................... [Enabled]


    Uncore & QPI Features:
    QPI Link Speed .............................. Auto
    Uncore Frequency .......................... Auto (2880)
    Isonchronous Frequency ..................[Enabled]


    Standard Clock Control:
    Base Clock (BCLK) Control ................ [Enabled]
    BCLK Frequency (MHz) .....................180
    PCI Express Frequency (MHz) ........... Auto

    C.I.A.2 [Disabled]

    Advanced Clock Control:
    CPU Clock Drive ..............................[800mV]
    PCI Express Clock Drive ................... [900mV]
    CPU Clock Skew ............................. [0ps]
    IOH Clock Skew ............................. [0ps]


    Advanced DRAM Features:
    Performance Enhance ...................... [Turbo]
    Extreme Memory Profile (X.M.P) ......... [Disabled]
    System Memory Multiplier (SPD) ........ [AUTO]
    DRAM Timing Selectable (SPD) .......... [Manual]

    Channel A + B + C

    Channel A Timing Settings:
    ##Channel A Standard Timing Control##
    CAS Latency Time ......................7
    tRCD ...................................7....
    tRP .....................................7....
    tRAS .....................................20..

    ##Channel A Advanced Timing Control##
    tRC .................................27....... (Should be = tRAS + tRP or above for stability)
    tRRD ..................................4.....
    tWTR ...................................4...
    tWR .....................................8...
    tWTP .......................................
    tWL ........................................ (tWTP Must = tWR + tWL + 4)
    tRFC ..................................60.....
    tRTP ....................................4...
    tFAW .....................................20.
    Command Rate (CMD) ................1

    ##Channel A Misc Timing Control##
    Round Trip Latency ...................



    Advanced Voltage Control:

    CPU
    Load Line Calibration ................. [Disabled]
    CPU Vcore ..............................Auto.
    QPI/VTT Voltage 1.150v ............Auto
    CPU PLL 1.800v .......................Auto

    MCH/ICH
    PCIE 1.500v ...........................Auto
    QPI PLL 1.100v .......................Auto
    IOH Core 1.100v .....................Auto
    ICH I/O 1.500v .......................Auto
    ICH Core 1.1v ........................Auto

    DRAM
    DRAM Voltage 1.500v .............Auto.
    DRAM Termination 0.750v [AUTO]
    Ch-A Data VRef. 0.750v [AUTO]
    Ch-B Data VRef. 0.750v [AUTO]
    Ch-C Data VRef. 0.750v [AUTO]
    Ch-A Address VRef. 0.750v [AUTO]
    Ch-B Address VRef. 0.750v [AUTO]
    Ch-C Address VRef. 0.750v [AUTO]


    so basicly I only changed bclk to 180
    and memory timings

    and system won't boot

    when memory timings are on auto - systems boots up, cpu-z shows timings 10-9-9-25 which are little to high I guess
    Tags: None
  • #2
    Re: i7 gigabyte ud5 - oc settings - help

    Try these >>>

    If you want 1600Mhz ram speed exactly you are going to have to use more Blck (200) or use less (160)


    Advanced CPU Features:
    CPU Clock Ratio ................................ [20x]
    Intel(R) Turbo Boost Tech .................. [Enabled]
    CPU Cores Enabled ............................ [All]
    CPU Multi Threading .......................... [Enabled]
    CPU Enhanced Halt (C1E) ................... [Enabled] << Disabled
    C3/C6/C7 State Support .................... [Enabled] << Disabled
    CPU Thermal Monitor ......................... [Enabled]
    CPU EIST Function ............................ [Enabled] << Disabled
    Virtualization Technology ................... [Enabled] << Disabled if you do not use Vmware or Virtual PC programs
    Bi-Directional PROCHOT ..................... [Enabled]


    Uncore & QPI Features:
    QPI Link Speed .............................. x36
    Uncore Frequency .......................... 16-17 (Memory Multi x 2)
    Isonchronous Frequency ..................[Enabled]


    Standard Clock Control:
    Base Clock (BCLK) Control ................ [Enabled]
    BCLK Frequency (MHz) .....................180
    PCI Express Frequency (MHz) ........... 100

    C.I.A.2 [Disabled]

    Advanced Clock Control:
    CPU Clock Drive ..............................[800mV]
    PCI Express Clock Drive ................... [900mV]
    CPU Clock Skew ............................. [0ps]
    IOH Clock Skew ............................. [0ps]


    Advanced DRAM Features:
    Performance Enhance ...................... [Turbo] << Set standard for now
    Extreme Memory Profile (X.M.P) ......... [Disabled]
    System Memory Multiplier (SPD) ........ [AUTO] << Set 8 for now for 1440Mhz
    DRAM Timing Selectable (SPD) .......... [Manual]

    Channel A + B + C

    *SORRY BUT.......*

    I need a link to your ram or the model # to best advise cause I do not even know if you are using 3x1/3x2/2x1/2x2? I will edit this once you provide that info

    Channel A Timing Settings:
    ##Channel A Standard Timing Control##
    CAS Latency Time ......................7
    tRCD ...................................7....
    tRP .....................................7....
    tRAS .....................................20..

    ##Channel A Advanced Timing Control##
    tRC .................................27....... (Should be = tRAS + tRP or above for stability)
    tRRD ..................................4.....
    tWTR ...................................4...
    tWR .....................................8...
    tWTP .......................................
    tWL ........................................ (tWTP Must = tWR + tWL + 4)
    tRFC ..................................60..... 82
    tRTP ....................................4...
    tFAW .....................................20.
    Command Rate (CMD) ................1

    ##Channel A Misc Timing Control##
    Round Trip Latency ...................



    Advanced Voltage Control:

    CPU
    Load Line Calibration ................. [Disabled]
    CPU Vcore ..............................1.2-1.425 actual shown in CPU-z (All up to your CPU, you cannot use Auto though when overclocking so get ready to try to find your Vcore)

    QPI/VTT Voltage 1.150v ............ Set 1.2-1.35 (All depends on Ram/QPI/uncore speeds)
    CPU PLL 1.800v .......................1.8-1.84 should be good

    MCH/ICH
    PCIE 1.500v ...........................1.54
    QPI PLL 1.100v .......................1.1-1.2 should be good
    IOH Core 1.100v .....................1.1-1.24+ (Need to know ram)
    ICH I/O 1.500v .......................1.5
    ICH Core 1.1v .......................1.14-1.24

    DRAM
    DRAM Voltage 1.500v .............1.64-1.68
    DRAM Termination 0.750v [AUTO]
    Ch-A Data VRef. 0.750v [AUTO]
    Ch-B Data VRef. 0.750v [AUTO]
    Ch-C Data VRef. 0.750v [AUTO]
    Ch-A Address VRef. 0.750v [AUTO]
    Ch-B Address VRef. 0.750v [AUTO]
    Ch-C Address VRef. 0.750v [AUTO]

    Comment

    • #3
      Re: i7 gigabyte ud5 - oc settings - help

      here is a link to my memory:


      Patriot Memory - Products

      I'll let you know if it worked

      thanks a lot

      Comment

      • #4
        Re: i7 gigabyte ud5 - oc settings - help

        here are my current settings:

        Advanced CPU Features:
        CPU Clock Ratio ................................ [20x]
        Intel(R) Turbo Boost Tech .................. [Enabled]
        CPU Cores Enabled ............................ [All]
        CPU Multi Threading .......................... [Enabled]
        CPU Enhanced Halt (C1E) ................... Disabled
        C3/C6/C7 State Support .................... Disabled
        CPU Thermal Monitor ......................... [Enabled]
        CPU EIST Function ............................ Disabled
        Virtualization Technology ................... Disabled
        Bi-Directional PROCHOT ..................... [Enabled]


        Uncore & QPI Features:
        QPI Link Speed .............................. x36
        Uncore Frequency .......................... 16
        Isonchronous Frequency ..................[Enabled]


        Standard Clock Control:
        Base Clock (BCLK) Control ................ [Enabled]
        BCLK Frequency (MHz) .....................180
        PCI Express Frequency (MHz) ........... 100

        C.I.A.2 [Disabled]

        Advanced Clock Control:
        CPU Clock Drive ..............................[800mV]
        PCI Express Clock Drive ................... [900mV]
        CPU Clock Skew ............................. [0ps]
        IOH Clock Skew ............................. [0ps]


        Advanced DRAM Features:
        Performance Enhance ...................... Standard
        Extreme Memory Profile (X.M.P) ......... [Disabled]
        System Memory Multiplier (SPD) ........ 8
        DRAM Timing Selectable (SPD) .......... [Manual]

        Channel A + B + C

        *SORRY BUT.......*

        I need a link to your ram or the model # to best advise cause I do not even know if you are using 3x1/3x2/2x1/2x2? I will edit this once you provide that info

        ------

        Patriot Memory - Products

        ------


        Channel A Timing Settings:
        ##Channel A Standard Timing Control##
        CAS Latency Time ......................8
        tRCD ...................................8
        tRP .....................................8
        tRAS .....................................24

        ##Channel A Advanced Timing Control##
        tRC .................................auto
        tRRD ..................................auto
        tWTR ..................................auto
        tWR .....................................auto
        tWTP .......................................can't find it in bios
        tWL ........................................ can't find it in bios
        tRFC ..................................auto
        tRTP ....................................auto
        tFAW .....................................auto
        Command Rate (CMD) ................tried 1 or 2

        ##Channel A Misc Timing Control##
        Round Trip Latency ...................auto



        Advanced Voltage Control:

        CPU
        Load Line Calibration ................. [Disabled]
        CPU Vcore ..............................1,375

        QPI/VTT Voltage 1.150v ............ 1,28
        CPU PLL 1.800v .......................1,8

        MCH/ICH
        PCIE 1.500v ...........................1.54
        QPI PLL 1.100v .......................1,14
        IOH Core 1.100v .....................1,14
        ICH I/O 1.500v .......................1.5
        ICH Core 1.1v .......................1,2

        DRAM
        DRAM Voltage 1.500v .............1.64
        DRAM Termination 0.750v [AUTO]
        Ch-A Data VRef. 0.750v [AUTO]
        Ch-B Data VRef. 0.750v [AUTO]
        Ch-C Data VRef. 0.750v [AUTO]
        Ch-A Address VRef. 0.750v [AUTO]
        Ch-B Address VRef. 0.750v [AUTO]
        Ch-C Address VRef. 0.750v [AUTO]


        system won't boot when I set timings manually

        with above settings, after setting DRAM Timing Selectable to auto it boots and cpu-z shows 10-10-10-28 and CR = 1T


        I guess my problem is memory?

        Comment

        • #5
          Re: i7 gigabyte ud5 - oc settings - help

          Try this >>>

          Advanced CPU Features:
          CPU Clock Ratio ................................ [20x]
          Intel(R) Turbo Boost Tech .................. [Enabled]
          CPU Cores Enabled ............................ [All]
          CPU Multi Threading .......................... [Enabled]
          CPU Enhanced Halt (C1E) ................... Disabled
          C3/C6/C7 State Support .................... Disabled
          CPU Thermal Monitor ......................... [Enabled]
          CPU EIST Function ............................ Disabled
          Virtualization Technology ................... Disabled
          Bi-Directional PROCHOT ..................... [Enabled]


          Uncore & QPI Features:
          QPI Link Speed .............................. x36
          Uncore Frequency .......................... 16 << Try 17 it is better and should be fine, but you can leave 16 for now if you like
          Isonchronous Frequency ..................[Enabled]


          Standard Clock Control:
          Base Clock (BCLK) Control ................ [Enabled]
          BCLK Frequency (MHz) .....................180
          PCI Express Frequency (MHz) ........... 100

          C.I.A.2 [Disabled]

          Advanced Clock Control:
          CPU Clock Drive ..............................[800mV]
          PCI Express Clock Drive ................... [900mV]
          CPU Clock Skew ............................. [0ps]
          IOH Clock Skew ............................. [0ps]


          Advanced DRAM Features:
          Performance Enhance ...................... Standard
          Extreme Memory Profile (X.M.P) ......... [Disabled]
          System Memory Multiplier (SPD) ........ 8
          DRAM Timing Selectable (SPD) .......... [Manual]

          Channel A + B + C

          *SORRY BUT.......*

          I need a link to your ram or the model # to best advise cause I do not even know if you are using 3x1/3x2/2x1/2x2? I will edit this once you provide that info

          ------

          Patriot Memory - Products

          ------


          Channel A Timing Settings:
          ##Channel A Standard Timing Control##
          CAS Latency Time ......................8
          tRCD ...................................8
          tRP .....................................8
          tRAS .....................................24

          ##Channel A Advanced Timing Control##
          tRC .................................32-34
          tRRD ..................................4-6
          tWTR ..................................4-6
          tWR ....................................8-12
          tWTP .......................................can't find it in bios
          tWL ........................................ can't find it in bios (Sorry must not be added for your model yet)
          tRFC ..................................72-84
          tRTP ....................................4-6
          tFAW .....................................30-34
          Command Rate (CMD) ................1

          ##Channel A Misc Timing Control##
          Round Trip Latency ...................auto



          Advanced Voltage Control:

          CPU
          Load Line Calibration ................. [Disabled]
          CPU Vcore ..............................1,375 << Set more then this for now since you have LLC Disabled as this may only be 1.32-1.34 or so and your CPU may need more. Or enable LLC

          QPI/VTT Voltage 1.150v ............ 1,28-1.36
          CPU PLL 1.800v .......................1,8-1.86

          MCH/ICH
          PCIE 1.500v ...........................1.54
          QPI PLL 1.100v .......................1,20-1.24 << Bring this down later but set 1.20-124 for now to be sure it is not a issue for you
          IOH Core 1.100v .....................1,16-1.24 << Set 1.2 for now, lower later
          ICH I/O 1.500v .......................1.5
          ICH Core 1.1v .......................1.14

          DRAM
          DRAM Voltage 1.500v .............1.64 << Set 1.68 as 1.64 is actually about 1.63 or less
          DRAM Termination 0.750v [AUTO]
          Ch-A Data VRef. 0.750v [AUTO]
          Ch-B Data VRef. 0.750v [AUTO]
          Ch-C Data VRef. 0.750v [AUTO]
          Ch-A Address VRef. 0.750v [AUTO]
          Ch-B Address VRef. 0.750v [AUTO]
          Ch-C Address VRef. 0.750v [AUTO]

          Comment

          • #6
            Re: i7 gigabyte ud5 - oc settings - help

            with your last settings system boots up


            Advanced CPU Features:
            CPU Clock Ratio ................................ [20x]
            Intel(R) Turbo Boost Tech .................. [Enabled]
            CPU Cores Enabled ............................ [All]
            CPU Multi Threading .......................... [Enabled]
            CPU Enhanced Halt (C1E) ................... Disabled
            C3/C6/C7 State Support .................... Disabled
            CPU Thermal Monitor ......................... [Enabled]
            CPU EIST Function ............................ Disabled
            Virtualization Technology ................... Disabled
            Bi-Directional PROCHOT ..................... [Enabled]


            Uncore & QPI Features:
            QPI Link Speed .............................. x36
            Uncore Frequency .......................... 17
            Isonchronous Frequency ..................[Enabled]


            Standard Clock Control:
            Base Clock (BCLK) Control ................ [Enabled]
            BCLK Frequency (MHz) .....................180
            PCI Express Frequency (MHz) ........... 100

            C.I.A.2 [Disabled]

            Advanced Clock Control:
            CPU Clock Drive ..............................[800mV]
            PCI Express Clock Drive ................... [900mV]
            CPU Clock Skew ............................. [0ps]
            IOH Clock Skew ............................. [0ps]


            Advanced DRAM Features:
            Performance Enhance ...................... Standard
            Extreme Memory Profile (X.M.P) ......... [Disabled]
            System Memory Multiplier (SPD) ........ 8
            DRAM Timing Selectable (SPD) .......... [Manual]

            Channel A + B + C


            Channel A Timing Settings:
            ##Channel A Standard Timing Control##
            CAS Latency Time ......................8
            tRCD ...................................8
            tRP .....................................8
            tRAS .....................................24

            ##Channel A Advanced Timing Control##
            tRC .................................32
            tRRD ..................................4
            tWTR ..................................4
            tWR ....................................8
            tWTP .......................................can't find it in bios
            tWL ........................................ can't find it in bios (Sorry must not be added for your model yet)
            tRFC ..................................72
            tRTP ....................................4
            tFAW .....................................30
            Command Rate (CMD) ................1

            ##Channel A Misc Timing Control##
            Round Trip Latency ...................auto



            Advanced Voltage Control:

            CPU
            Load Line Calibration ................. [Disabled]
            CPU Vcore ..............................1,4

            QPI/VTT Voltage 1.150v ............ 1,3
            CPU PLL 1.800v .......................1,84

            MCH/ICH
            PCIE 1.500v ...........................1.54
            QPI PLL 1.100v .......................1,20 << Bring this down later but set 1.20-124 for now to be sure it is not a issue for you
            IOH Core 1.100v .....................1,20 << Set 1.2 for now, lower later
            ICH I/O 1.500v .......................1.5
            ICH Core 1.1v .......................1.14

            DRAM
            DRAM Voltage 1.500v .............1.64 (everything above 1,64 was market pink- didn't know if it's safe to rise)
            DRAM Termination 0.750v [AUTO]
            Ch-A Data VRef. 0.750v [AUTO]
            Ch-B Data VRef. 0.750v [AUTO]
            Ch-C Data VRef. 0.750v [AUTO]
            Ch-A Address VRef. 0.750v [AUTO]
            Ch-B Address VRef. 0.750v [AUTO]
            Ch-C Address VRef. 0.750v [AUTO]



            cpu-z check out ok 8-8-8-24 1T

            should I now try to lower some of the voltages? what about dram performance enhance, leave it on standard?

            Comment

            • #7
              Re: i7 gigabyte ud5 - oc settings - help

              I noticed some stability problems with configuration below. Experienced several freezes, for example during video compression.

              Is it possible to change only memory frequency by lowering system memory multiplier and leaving other settings as they are?

              I feel that memory is causing problems and do not actually need them to work as 1600 mhz.




              Advanced CPU Features:
              CPU Clock Ratio ................................ [20x]
              Intel(R) Turbo Boost Tech .................. [Enabled]
              CPU Cores Enabled ............................ [All]
              CPU Multi Threading .......................... [Enabled]
              CPU Enhanced Halt (C1E) ................... Disabled
              C3/C6/C7 State Support .................... Disabled
              CPU Thermal Monitor ......................... [Enabled]
              CPU EIST Function ............................ Disabled
              Virtualization Technology ................... Disabled
              Bi-Directional PROCHOT ..................... [Enabled]


              Uncore & QPI Features:
              QPI Link Speed .............................. x36
              Uncore Frequency .......................... 17
              Isonchronous Frequency ..................[Enabled]


              Standard Clock Control:
              Base Clock (BCLK) Control ................ [Enabled]
              BCLK Frequency (MHz) .....................180
              PCI Express Frequency (MHz) ........... 100

              C.I.A.2 [Disabled]

              Advanced Clock Control:
              CPU Clock Drive ..............................[800mV]
              PCI Express Clock Drive ................... [900mV]
              CPU Clock Skew ............................. [0ps]
              IOH Clock Skew ............................. [0ps]


              Advanced DRAM Features:
              Performance Enhance ...................... Standard
              Extreme Memory Profile (X.M.P) ......... [Disabled]
              System Memory Multiplier (SPD) ........ 8
              DRAM Timing Selectable (SPD) .......... [Manual]

              Channel A + B + C

              Patriot Memory - Products


              Channel A Timing Settings:
              ##Channel A Standard Timing Control##
              CAS Latency Time ......................8
              tRCD ...................................8
              tRP .....................................8
              tRAS .....................................24

              ##Channel A Advanced Timing Control##
              tRC .................................32
              tRRD ..................................4
              tWTR ..................................4
              tWR ....................................8
              tWTP .......................................
              tWL ........................................
              tRFC ..................................72
              tRTP ....................................4
              tFAW .....................................30
              Command Rate (CMD) ................1

              ##Channel A Misc Timing Control##
              Round Trip Latency ...................auto



              Advanced Voltage Control:

              CPU
              Load Line Calibration ................. [Disabled]
              CPU Vcore ..............................1,4

              QPI/VTT Voltage 1.150v ............ 1,3
              CPU PLL 1.800v .......................1,84

              MCH/ICH
              PCIE 1.500v ...........................1.54
              QPI PLL 1.100v .......................1,20 << Bring this down later but set 1.20-124 for now to be sure it is not a issue for you
              IOH Core 1.100v .....................1,20 << Set 1.2 for now, lower later
              ICH I/O 1.500v .......................1.5
              ICH Core 1.1v .......................1.14

              DRAM
              DRAM Voltage 1.500v .............1.68
              DRAM Termination 0.750v [AUTO]
              Ch-A Data VRef. 0.750v [AUTO]
              Ch-B Data VRef. 0.750v [AUTO]
              Ch-C Data VRef. 0.750v [AUTO]
              Ch-A Address VRef. 0.750v [AUTO]
              Ch-B Address VRef. 0.750v [AUTO]
              Ch-C Address VRef. 0.750v [AUTO]

              Comment

              • #8
                Re: i7 gigabyte ud5 - oc settings - help

                disable "Intel(R) Turbo Boost Tech"
                X58A-UD7 Rev1 | Core i7 920 @ 191x21 4GHz | Thermalright Extreme 120 REV A | Corsair 6GB Dominator GT 1600 C7 | Sapphire HD4870 Toxic 1GB 800/1000 | Antec TPQ-850w

                Comment

                • #9
                  Re: i7 gigabyte ud5 - oc settings - help

                  hi, i'm very new at overclocking (actually never done it before).

                  i have a UD5 mobo, F10 bios, i7-920 CPU, a very large heatsink (ultra-120 extreme), and corsair dominator ram 3x2GB TR3X6G1600C8D G
                  This memory has been verified to operate at 1600MHz at latencies of 8-8-8-24 at 1.65V VDIMM.
                  can anyone help me figure out two things:

                  1. what settings i should use for overclocking (it's at 2.8GHz with the built in "extreme" setting)

                  2. how can i get the fans to automatically speed up/slow down based on temperatures? i'm trying to use speedfan but it's not doing anything

                  thanks very much!

                  Comment

                  • #10
                    Re: i7 gigabyte ud5 - oc settings - help

                    Originally posted by joe2 View Post
                    hi, i'm very new at overclocking (actually never done it before).

                    i have a UD5 mobo, F10 bios, i7-920 CPU, a very large heatsink (ultra-120 extreme), and corsair dominator ram 3x2GB TR3X6G1600C8D Gcan anyone help me figure out two things:

                    1. what settings i should use for overclocking (it's at 2.8GHz with the built in "extreme" setting)

                    2. how can i get the fans to automatically speed up/slow down based on temperatures? i'm trying to use speedfan but it's not doing anything

                    thanks very much!
                    makesure pwm is enabled in bios for your fans,or on auto,floow my overclock guide in my sig for 3.8ghz overclock
                    Gigabyte ex58-ud5 f12 bios
                    Intel i7 920 d0 @3.8ghz 24/7-normal cpu voltage 1.18750v/c1e/turbo/multi threading enabled
                    Ocz reaper DDR3 PC3-14400 (1800MHz) 3x2gb (OCZ3RPR1800LV6GK) [email protected]
                    Thermolab Baram cpu cooler
                    Dual Boot
                    1xsamsung 750gb hard drive-win7 ultimate 64
                    1xsamsung 750gb hard drive-windows xp pro 32
                    Ati x1950 pro gpu
                    Logitech X-530 5.1 Speakers
                    1050w psu
                    Nzxt lexa case
                    http://i40.tinypic.com/2z3w377.jpg <=3.8ghz overclock template

                    Comment

                    • #11
                      Re: i7 gigabyte ud5 - oc settings - help

                      Originally posted by warren300 View Post
                      makesure pwm is enabled in bios for your fans,or on auto,floow my overclock guide in my sig for 3.8ghz overclock
                      is that relevant with my RAM? or do i need to change anything?

                      Comment

                      • #12
                        Re: i7 gigabyte ud5 - oc settings - help

                        Originally posted by joe2 View Post
                        is that relevant with my RAM? or do i need to change anything?
                        pwm is for your cpu fan it makes it speed up when hot and slow down when cool,follow my guide to set your ram
                        Gigabyte ex58-ud5 f12 bios
                        Intel i7 920 d0 @3.8ghz 24/7-normal cpu voltage 1.18750v/c1e/turbo/multi threading enabled
                        Ocz reaper DDR3 PC3-14400 (1800MHz) 3x2gb (OCZ3RPR1800LV6GK) [email protected]
                        Thermolab Baram cpu cooler
                        Dual Boot
                        1xsamsung 750gb hard drive-win7 ultimate 64
                        1xsamsung 750gb hard drive-windows xp pro 32
                        Ati x1950 pro gpu
                        Logitech X-530 5.1 Speakers
                        1050w psu
                        Nzxt lexa case
                        http://i40.tinypic.com/2z3w377.jpg <=3.8ghz overclock template

                        Comment

                        • #13
                          Re: i7 gigabyte ud5 - oc settings - help

                          Originally posted by warren300 View Post
                          pwm is for your cpu fan it makes it speed up when hot and slow down when cool,follow my guide to set your ram
                          yeah i meant your guide - what settings should i change for my ram?

                          Comment

                          • #14
                            Re: i7 gigabyte ud5 - oc settings - help

                            whats it say on your ram module?timings and volts? set the bios to that something like 8-8-8-24-command rate 1T select quick timings and enter timings
                            Gigabyte ex58-ud5 f12 bios
                            Intel i7 920 d0 @3.8ghz 24/7-normal cpu voltage 1.18750v/c1e/turbo/multi threading enabled
                            Ocz reaper DDR3 PC3-14400 (1800MHz) 3x2gb (OCZ3RPR1800LV6GK) [email protected]
                            Thermolab Baram cpu cooler
                            Dual Boot
                            1xsamsung 750gb hard drive-win7 ultimate 64
                            1xsamsung 750gb hard drive-windows xp pro 32
                            Ati x1950 pro gpu
                            Logitech X-530 5.1 Speakers
                            1050w psu
                            Nzxt lexa case
                            http://i40.tinypic.com/2z3w377.jpg <=3.8ghz overclock template

                            Comment

                            • #15
                              Re: i7 gigabyte ud5 - oc settings - help

                              Originally posted by warren300 View Post
                              whats it say on your ram module?timings and volts? set the bios to that something like 8-8-8-24-command rate 1T select quick timings and enter timings
                              This memory has been verified to operate at 1600MHz at latencies of 8-8-8-24 at 1.65V VDIMM.

                              Comment

                              Previous 1 2 template Next
                              Working...
                              X