Need some help please

[The Muncher]

I'm trying to get my sig rig stable @ 4.0. Yeah I know it might not be possable.I have had it running at 3.6 for the last month and as high as 3.9 but it wasnt stable. I'm sorry i cant remember the settings,I have tried to lower the multi to as low as 6 and up the FSB but it just wont post. How do i d/load the templet? I just updated the bios to the lasted 8 on the gigabyte site.Could someone give me some settings to try out.

My chip E7200 2.53 revision MO

Thanks in advance

[The Muncher]

Re: Need some help please

I found a templet that was made by LSDMEASAP for a e5200,its the same core as mine (wolfdale) It running ok.<---I say this because as I'm typing this and listening to music it started to wig out but it didn't shut down. I'm not sure what i need to change.........
It seems that if i change the setting in the MCH Reference slot the comp wont boot. I'm running at 400x9.5=3.8,I guess I'll have to lower to see it will be stable in prime.I did prime and core 1 failed right away. How do I d/load the templets so I can show on the site?

[Lsdmeasap]

Re: Need some help please

Nice avatar!!!

I think I know you from AB or AW right?

Please link me to your memory or give me the model #, and then your full settings. To Post the settings you just will have to copy this, fill it in and post it back. >>>

This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

[b][u]MB Intelligent Tweaker(M.I.T.)[/u][/b]
Robust Graphics Booster ...............: Auto or Fast
CPU Clock Ratio ..........................: 
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 


[b][u]Clock Chip Control [/u][/b]
[b][u]Standard Clock Control[/u][/b]
CPU Host Clock Control..................: [Enabled] 
CPU Host Frequency (Mhz) ............: Mhz
[B]PCI Express Frequency (Mhz) .........:Set to 100[/B]

C.I.A.2 .................................:[Disabled]


[b][u]Advanced Clock Control [Press Enter][/u][/b]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 
MCH Clock Skew (ps)...................: <<< 


[b][u]DRAM Performance Control[/u][/b][u][/u]
[B]Performance Enhance...................: [STANDARD][/B]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 
Memory Frequency (Mhz) ..............: 
DRAM Timing Selectable ................: [Manual]

[b]Standard Timing Control[/b]
CAS Latency Time........................
tRCD .........................................
tRP'...........................................
tRAS..........................................

Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go

[b][u]Advanced Timing Control[/u][/b]
tRRD...........................................
tWTR..........................................
tWR............................................
tRFC...........................................
tRTP...........................................
Command Rate (CMD) ....................:2

[u][b]Driving Strength Profiles[/b][/u][b][/b]
Driving Strength ............................

[b]Channel A[/b]
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
 tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

[b]Channel B[/b]
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
 tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

[b][U]Motherboard Voltage Control[/U][/b][U][/U]
Voltage Type.………... Manual
[b]CPU[/b]
CPU Vcore….……….........................:Auto if not overclocking, if you are overclocking please do find and set your own voltages

CPU Termination…..... 1.200V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.2-1.5 depending on Vcore, try to keep at least .1 under vcore.  Auto is fine if not overclocking

CPU PLL…………………....1.500V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.5-1.65.  Auto is fine if not overclocking

CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 

CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly 

[b]MCH/ICH[/b]
MCH Core…………….....1.100V...........: << 
MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.500V............: <<< Leave
ICH Core…………...……1.100V............: <<< Leave

[b]DRAM[/b]
DRAM Voltage ……....1.800V............: 
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

[b][U]Advanced Settings[/U][/b][U][/U]
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

[b][U]Integrated Peripherals[/U][/b][U][/U]
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

[The Muncher]

Re: Need some help please

How you i repost the templet into my next post?

[The Muncher]

Re: Need some help please

Nice avatar!!!

I think I know you from AB or AW right?

Please link me to your memory or give me the model #, and then your full settings. To Post the settings you just will have to copy this, fill it in and post it back. >>>

This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

[B][U]MB Intelligent Tweaker(M.I.T.)[/U][/B]
Robust Graphics Booster ...............: Auto or Fast
CPU Clock Ratio ..........................: 9.5
Fine CPU Clock Ratio.....................:.0.5
CPU Frequency ...........................: 400x9.5=3.8
 
 
[B][U]Clock Chip Control [/U][/B]
[B][U]Standard Clock Control[/U][/B]
CPU Host Clock Control..................: [Enabled] 
CPU Host Frequency (Mhz) ............: Mhz400
[B]PCI Express Frequency (Mhz) .........:Set to 100[/B]
 
C.I.A.2 .................................:[Disabled]
 
 
[B][U]Advanced Clock Control [Press Enter][/U][/B]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 0ps
MCH Clock Skew (ps)...................: <<< 0ps
 
 
[B][U]DRAM Performance Control[/U][/B]
[B]Performance Enhance...................: [STANDARD][/B]
Extreme Memory Profile (X.M.P.).....: Disabled-auto
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 200B
Memory Frequency (Mhz) ..............: 800
DRAM Timing Selectable ................: [Manual]
 
[B]Standard Timing Control[/B]
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................15
 
Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go
 
[B][U]Advanced Timing Control[/U][/B]
tRRD...........................................4 all set by computer
tWTR..........................................4
tWR............................................13
tRFC...........................................68
tRTP...........................................4
Command Rate (CMD) ....................:2
 
[U][B]Driving Strength Profiles[/B][/U]
Driving Strength ............................1066
 
[B]Channel A[/B]
Static tRead Value.........................:9 
 tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps
 
[B]Channel B[/B]
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH 9
 tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps
 
[B][U]Motherboard Voltage Control[/U][/B]
Voltage Type.���... Manual
[B]CPU[/B]
CPU Vcore�.���.........................:Auto if not overclocking, if you are overclocking please do find and set your own voltages 135625v
 
CPU Termination�..... 1.200V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.2-1.5 depending on Vcore, try to keep at least .1 under vcore.  Auto is fine if not overclocking 1300v
 
CPU PLL�������....1.500V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.5-1.65.  Auto is fine if not overclocking 1570v
 
CPU Referen.����....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 0.848v 
 
CPU Reference2���,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly 
 
[B]MCH/ICH[/B]
MCH Core�����.....1.100V...........: << any setting otherthen  auto peeps on start up and never posts
MCH Reference�.��.0.800V...........; <<< Leave
MCH/DRAM Ref.�......0.900V...........: <<< Leave
ICH I/O������.....1.500V............: <<< Leave 1.570v
ICH Core����...��1.100V............: <<< Leave 1.00v
 
[B]DRAM[/B]
DRAM Voltage ��....1.800V............: 2.1v
DRAM Termination .�0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave
 
[B][U]Advanced Settings[/U][/B]
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
 
[B][U]Integrated Peripherals[/U][/B]
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

E7200 2.52 9.5 multi MO revision
gigabyte UD3P virson 1.0
ram Newegg.com - G.SKILL 4GB &#40;2 x 2GB&#41; 240-Pin DDR2 SDRAM DDR2 1066 &#40;PC2 8500&#41; Dual Channel Kit Desktop Memory - Desktop Memory

No, I dont know you from any other site,I hope this helps. Thanks in advance

[Nickel020]

Re: Need some help please

I also have an E7200 here and I have trouble on my EP45 DS3L getting the FSB above 400 MHz, tried all kinds of voltages, RAM is definitely not an issue, nor is cooling. I'll try it on the UD3P tomorrow, but I think these chips jsut don't overclock as well as the E8x00 CPUs do.

[The Muncher]

Re: Need some help please

Thanks Nickel020,
Yeah I think the 8*** are the best o/c-ers

[Lsdmeasap]

Re: Need some help please

Hmm, thats odd about you not knowing me. I have seen that same image and Same exact signature used before? Maybe you or him copied it then?

Ya 7x000's don't clock as well for sure, hence the price

See if this helps any >>>

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto or Fast
CPU Clock Ratio ..........................: 9.5
Fine CPU Clock Ratio.....................:.0.5
CPU Frequency ...........................: 400x9.5=3.8


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: Mhz400 << use 401
PCI Express Frequency (Mhz) .........:Set to 100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 0ps
MCH Clock Skew (ps)...................: <<< 0ps


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 200B << Try 2.00D
Memory Frequency (Mhz) ..............: 800
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................15

Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go

Advanced Timing Control
tRRD...........................................4 all set by computer (? Auto you mean? Set manually) 3-4
tWTR..........................................6
tWR............................................8
tRFC...........................................58
tRTP...........................................4
Command Rate (CMD) ....................:2

Driving Strength Profiles
Driving Strength ............................1066

Channel A
Static tRead Value.........................:10
tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:10
tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................:Auto if not overclocking, if you are overclocking please do find and set your own voltages 135625v << you may need more then this, this is less once windows starts and even less under load so keep that in mind

CPU Termination…..... 1.200V*.......: << If overclocking Please set to stock, Auto overvolts this way to much. Optimal range for overclock would be 1.2-1.5 depending on Vcore, try to keep at least .1 under vcore. Auto is fine if not overclocking 1300v << Try 1.28 and 1.32-1.34

CPU PLL…………………....1.500V*.......: << If overclocking Please set to stock, Auto overvolts this way to much. Optimal range for overclock would be 1.5-1.65. Auto is fine if not overclocking 1570v

CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 0.848v << Use Auto

CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly

MCH/ICH
MCH Core…………….....1.100V...........: << 1.24 (Your Static tRead may be the issue here maybe not?) Try 1.24 and then also try 1.05

MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.500V............: <<< Leave 1.570v
ICH Core…………...……1.100V............: <<< Leave 1.14v

DRAM
DRAM Voltage ……....1.800V............: 2.1v
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

[The Muncher]

Re: Need some help please

What ar the two sites you thought you saw me on?
Is it the picture?
or the sheet sandwhich?
the muncher is just a name i came up with since ive been on this site,most of the time my screen name is Barry.

The picture i found on the net and have had it beside my name for about a year
the sheet sandwhich was something my boss told me about 20yrs ago and ive had it in my sig for about a yr in the sites that wont say anything about it

Im going to try some of your settings,thanks for taking the time to figure it out.

[The Muncher]

Re: Need some help please

LSDMEASAP,
I dont know how you come up with these settings but........ my computer is primming its azz off and never get over 60c,your the man

[Lsdmeasap]

Re: Need some help please

HAHA, It is the Avatar and the <------Hot azz part

Only, sorry I did not mean the sheet sandwich part

The sites I thought I knew you from are sites I would not mention here, and do not frequent anymore just because I got out of that kinda thing a while ago.

The ones I mentioned above AB/AW were both Album places. But really, I may have just noticed that at any number of other sites I used to frequent or mod/admin at. Places to get free things basically, ya know where people post stuff, and others download, and then share again and so on.

Nice to see your PC Is priming away!! I get them all out of my head, years of tweaking hard at work inside there

If you get errors let me know what Prime mode you was running, how long until it error'd and if you ran memtest86+ beforehand or not. Then of course post me the settings you used that failed and I will advise back