UD3 +GSkill 6400black PI limits.

[kick]

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster .................: [Auto]
CPU Clock Ratio ............................: [7x]
CPU Frequency .............................: 3.01GHz [3.5Ghz*]

Clock Chip Control
Standard Clock Control
CPU Host Clock Control......................: [Enabled]
CPU Host Frequency (Mhz) ................: [430][500*]
PCI Express Frequency (Mhz) .............: 100
C.I.A.2 ..........................................: [Disabled]

Advanced Clock Control [Press Enter]
CPU Clock Drive............................: [1000mV]auto*
PCI Express Clock Drive..................: [1000mV]auto*
CPU Clock Skew (ps).....................: [ 0 ps]
MCH Clock Skew (ps).....................: [0 ps]

DRAM Performance Control
Performance Enhance........................: [Standard]turbo*
(G)MCH Frequency Latch....................: [auto]
System Memory Multiplier ..................: [2.40B]2.0B*
Memory Frequency (Mhz) ...............: [1032]1000*
DRAM Timing Selectable ..................: [Manual]

Standard Timing Control
CAS Latency Time....................... [5]5*
tRCD ........................................ [5]5*
tRP'.......................................... [4/5]5*
tRAS....................................... [15/18]15*

Advanced Timing Control
tRRD................................... [Auto]
tWTR................................... [Auto]
tWR.................................... [Auto]
tRFC................................... [Auto/66 shown in memset]48/52*
tRTP................................... [Auto]
Command Rate (CMD) ....................[2T]




Driving Strength Profiles
Driving Strength .........................[Auto]


Channel A
Static tRead Value..................... [9/10/11]9/10*
tRD Phase0 Adjustment.................. [Auto]
tRD Phase1 Adjustment.................. [Auto]
tRD Phase2 Adjustment ................. [Auto]
tRD Phase3 Adjustment.................. [Auto]
Trd2rd(Different Rank)................. [Auto]
Twr2wr(Different Rank)................. [Auto]
Twr2rd(Different Rank)................. [Auto]
Trd2wr(Same/Diff Rank)................. [Auto]
Dimm1 Clock Skew Control............... [Auto]
Dimm2 Clock Skew Control............... [Auto]
DDR Write Training..................... [Auto]

Channel B
Static tRead Value..................... [9/10/11]9/10*
tRD Phase0 Adjustment.................. [Auto]
tRD Phase1 Adjustment.................. [Auto]
tRD Phase2 Adjustment ................. [Auto]
tRD Phase3 Adjustment.................. [Auto]
Trd2rd(Different Rank)................. [Auto]
Twr2wr(Different Rank)................. [Auto]
Twr2rd(Different Rank)................. [Auto]
Trd2wr(Same/Diff Rank)................. [Auto]
Dimm1 Clock Skew Control............... [Auto]
Dimm2 Clock Skew Control............... [Auto]
DDR Write Training.....................[Auto]



Motherboard Voltage Control
Voltage Type Normal Current
CPU Vcore........................ 1.35V [1.39375V*]
CPU Termination.................. [auto]
CPU PLL............................. 1.500V [Auto]
CPU Referen........................ 0.760V [Auto]



MCH/ICH
MCH Core........................... 1.400V [1.38V*]
MCH Reference.................... 0.760V [Auto]
MCH/DRAM Ref..................... 1.150V [Auto*]
ICH I/O........................... 1.500V [Auto]
ICH Core......................... 1.100V [Auto]
DRAM
DRAM Voltage..................... 2.300V [2.18V*]
DRAM Termination................. 1.150V [Auto*]
Channel A Reference ............. 1.150V [Auto*]
Channel B Reference ............. 1.150V [Auto*]

These figures indicate what I needed to set in bios to get my memory stable at 1030 Mhz.
I only ran memtest ,I didnt bother with prime,because I had cpu set slower than normal to remove it from the equation.
I was hoping I would get a breakthro voltage/setting where I could clock to 1066 stable.
It wasnt happening
At the rate I was going I would run out of increased voltages long before 1066,and no point in commiting memory suicide.
The figures with an * are what the pc uses for 500mhz fsb 3.5Ghz cpu.
490 figures are in sig.

It seems I am stuck there unless someone has more info.
Ive seen 3 other reports of this mem having a 1000mhz limit on ud3s.
My other options are get a higher multiplier quad or some 1066 mem.
Since no ones giving those away just now,ill be ok as is.Seems fast enough and I dont know how high Q8200 can go on air on these anyway.