I need help

[majr70]

Hello i need that someone help me about a problem with my memories.
My computer:

-Gigabyte ep45 ds3r bios f10
-2x2 gb kingston hiperx 1066
-intel q6600@3200
-sapphire radeon 4870
-nox urano 600w

My problem is that these memories dont work at 1066@5,5,5,15800@4,4,4,10.

Sorry for my english.

[chuckm]

Re: I need help

raise mch

[SpeedEuphoria]

Re: I need help

you may need to tweak the mch ref value, but 1st try manually setting the PL(static tRead) to like 10. Then see if it boots. If not, try switching the mem stick positions, so 1>3 and 3>1, try it. If not Try 1 stick at a time and run memtest if it will boot fine with 1 stick at 1066

[Lsdmeasap]

Re: I need help

Ya, I would start with a high PL (Static tRead/tRD) at 9-10 and then add some MCH Voltage and set ram voltage to 2.1. Try MCH Core Voltage of 1.2-1.24 and see if that helps

What FSB are you using for your CPU? This matters because you need to choose your memory multiplier based on this FSB Setting.

Please to make it easier give us your full settings that are failing and a link to your ram or the model # and we will advise back >>>

This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

[b][u]MB Intelligent Tweaker(M.I.T.)[/u][/b]
Robust Graphics Booster ...............: Auto or Fast
CPU Clock Ratio ..........................: 
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 


[b][u]Clock Chip Control [/u][/b]
[b][u]Standard Clock Control[/u][/b]
CPU Host Clock Control..................: [Enabled] 
CPU Host Frequency (Mhz) ............: Mhz
[B]PCI Express Frequency (Mhz) .........:Set to 100[/B]

C.I.A.2 .................................:[Disabled]


[b][u]Advanced Clock Control [Press Enter][/u][/b]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 
MCH Clock Skew (ps)...................: <<< 


[b][u]DRAM Performance Control[/u][/b][u][/u]
[B]Performance Enhance...................: [STANDARD][/B]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 
Memory Frequency (Mhz) ..............: 
DRAM Timing Selectable ................: [Manual]

[b]Standard Timing Control[/b]
CAS Latency Time........................
tRCD .........................................
tRP'...........................................
tRAS..........................................

Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go

[b][u]Advanced Timing Control[/u][/b]
tRRD...........................................
tWTR..........................................
tWR............................................
tRFC...........................................
tRTP...........................................
Command Rate (CMD) ....................:2

[u][b]Driving Strength Profiles[/b][/u][b][/b]
Driving Strength ............................

[b]Channel A[/b]
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
 tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

[b]Channel B[/b]
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
 tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

[b][U]Motherboard Voltage Control[/U][/b][U][/U]
Voltage Type.………... Manual
[b]CPU[/b]
CPU Vcore….……….........................:Auto if not overclocking, if you are overclocking please do find and set your own voltages

CPU Termination…..... 1.200V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.2-1.5 depending on Vcore, try to keep at least .1 under vcore.  Auto is fine if not overclocking

CPU PLL…………………....1.500V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.5-1.65.  Auto is fine if not overclocking

CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 

CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly 

[b]MCH/ICH[/b]
MCH Core…………….....1.100V...........: << 
MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.550V............: <<< Leave
ICH Core…………...……1.100V............: <<< Leave

[b]DRAM[/b]
DRAM Voltage ……....1.800V............: 
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

[b][U]Advanced Settings[/U][/b][U][/U]
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

[b][U]Integrated Peripherals[/U][/b][U][/U]
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

[majr70]

Re: I need help

This is my configuration in bios:

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 8
Fine CPU Clock Ratio.....................:.0(No)
CPU Frequency ...........................: 3200(400x8)


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 400 Mhz
PCI Express Frequency (Mhz) .........:100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 700
PCI Express Clock Drive.................: <<< 700
CPU Clock Skew (ps)....................: <<< auto
MCH Clock Skew (ps)...................: <<< auto


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled(NO)
(G)MCH Frequency Latch...............: 400
System Memory Multiplier ..............: 2.66d
Memory Frequency (Mhz) ..............: 1066
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................15

Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go

Advanced Timing Control
tRRD...........................................aut o
tWTR..........................................auto
tWR............................................aut o
tRFC...........................................aut o
tRTP...........................................aut o
Command Rate (CMD) ....................:2

Driving Strength Profiles
Driving Strength ............................(no)

Channel A
Static tRead Value.........................:11
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:11
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage ControlCPUMCH/ICHDRAMAdvanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [enabled]
C2/C2E State Support....................: [Disabled](no)
x C4/C4E State Support..................: [Disabled](no)
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Enabled]
Virtualization Technology................: [enabled]

Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled]

Thank you

[majr70]

Re: I need help

And my memories:

http://www.valueram.com/datasheets/KHX8500D2_2G.pdf

[szacsee]

Re: I need help

Hy!
This is the default settings:

Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< auto
MCH Clock Skew (ps)...................: <<< auto

OC not work 700/700mV in Clock Drive settings.

Sorry my bad english.

[majr70]

Re: I need help

Hy!
This is the default settings:

Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< auto
MCH Clock Skew (ps)...................: <<< auto

OC not work 700/700mV in Clock Drive settings.

Sorry my bad english.

[majr70]

Re: I need help

you may need to tweak the mch ref value, but 1st try manually setting the PL(static tRead) to like 10. Then see if it boots. If not, try switching the mem stick positions, so 1>3 and 3>1, try it. If not Try 1 stick at a time and run memtest if it will boot fine with 1 stick at 1066

Hello, i have change the mem stick positions, 1 to 2 and 3 to 4 (red) and work fine at 5,5,5,15@1066. Do you think if the 1 and 3 positions are broken?
Thaks and sorry for my little english

[Lsdmeasap]

Re: I need help

Hmm, You will need to do some more testing to see if you have bad slots on your board.

Please try with One stick of ram in slot 1, then 2, then 3, and then 4 to be sure all slots are ok.

If they are you should be using 1+3 or 2+4 for Dual channel memory.

About your Clock Drive voltage questions. You need to load and apply optimized defaults, then save and reboot back to the BIOS and they will be changed and working. Manually changing them may not work as many hidden settings will also be set incorrect since you loaded fail safe settings.

So please load optimized, then save and apply and reboot back to the BIOS and then set all your settings again. DO NOT FORGET SATA and Other DISK Settings you WILL HAVE TO Set them all again before you load windows.

Once you are sure you have working memory slots I can advise you about your settings