Latest Overclocking Programs, System Info, Benchmarking, & Stability Tools

[Octopuss]

Re: Latest Overclocking Programs, System Info, Benchmarking, & Stability Tools

How can a program that reads SMART info from a HDD damage it?

[Darkje]

Re: Latest Overclocking Programs, System Info, Benchmarking, & Stability Tools

it was caused by the drive firmware, samsung released an update for it: SamsungF4EGBadBlocks

[stasio]

Re: Latest Overclocking Programs, System Info, Benchmarking, & Stability Tools

Updated with:

Realtek Lan Driver-7.033 1125.2010 (Win 7 32/64)

ThrottleStop 2.90 Beta 6

ThrottleStop 2.90 Beta 6

A couple of very minor updates. Moved the new real time VID data over beside where you set the VID and increased the maximum PowerSaver C0% to 100% in the Options window so you can run at full load with SLFM enabled if you want


ThrottleStop 2.90 beta 5

JKleiss: added the ability to save the benchmark results from one session to the next. Also added a checksum feature to keep everyone honest and added a Reset button to the TS Bench module so you can clear all of your times and start fresh.

RickiBerlin: added VID voltage reporting for Core 2 CPUs. In the above example, the VID request is set to 1.0500 but because Power Saver and SLFM are enabled, the CPU is using its lowest SLFM VID voltage which is 0.9500. That is now reported in the monitoring area.

ilguercio: added a new INI file option to access a lower CPU speed on the Core 2 CPUs with 200 MHz bus speeds.

SuperSLFM=1

On these CPUs, SLFM mode drops the bus speed from 200 MHz to 100 MHz at idle and then increases the multiplier to 8.0 for a total of

8.0 x 100 MHz = 800 MHz

If you have a Core 2 CPU like a T7250 or T8100, adding the above option to the ThrottleStop.INI configuration file will drop your CPU speed down to this at idle

6.0 x 100 MHz = 600 MHz

This speed is not officially supported by Intel but RM Clock lets you do this trick so now, ThrottleStop lets you do this too.

I also added a few options for myself.

The Battery button has been upgraded with some more information. You can now click on the Batt button and toggle the info from:

1) Battery Percent remaining.

2) Estimated Battery run time when on battery power.

3) System Power Consumption in watts when on battery power and charging rate in watts when plugged in.

4) and finally Maximum Battery Capacity in Wh, aka. watt hours.

If your battery is rated at 50 Wh and draws 20 W when you are using it then you should get about 50 / 20 = 2.5 hours (2:30) of run time out of a full charge.

Almost forgot. Added a DC Exit Time option to the Options window for Nando4. You can use this option to force ThrottleStop to close after a pre-selected amount of time in seconds. Some people don't like running ThrottleStop on battery power so if you set this value to 10, ThrottleStop will automatically exit approximately 10 seconds after you switch from DC to AC. Minimum value is 1.


ThrottleStop 2.90 beta 4

added a new benchmarking feature to ThrottleStop so it will be easier to get some quick feedback whether your adjustments are improving performance or not.

SetFSB 2.3.159.125

Added ICS952011BF(Shuttle XPC G 5690).
Fixed ICS9LPRS430BGLF(ExoPC Slate).
Included MSI Wind L1350(ICS9LPRS113AKLF).
Included ASUS K50IJ(ICS9LPR362AGLF).
Included Philco PHN 15008(ICS9LPR363EGLF).
Included ASUS 1015PN(ICS9LPR427AGLF).
Included Clavo M761SU/M7XOSU OEM(ICS9LPR600CGLF).
Included ASUS Maximus II Formula(ICS9LPRS918BKL).
Included ASUS UL50VG(ICS9LR3362CGLF).
Included Dell XPS 8100(CV183APAG).
Included Foxconn Bengal RS780(RTM880T-792).
Included Samsung R522-Satin/R620(SL28541BQC).
Included Toshiba T115D-S1120(SLG8SP626V).

GPU-Z Test Build

- Adds support for HD 6950 and HD 6970
- Fixes fillrate rounding error on GTX 400 cards

CrystalDiskInfo v3.9.4

- Added workaround for SAMSUNG HD155UI/HD204UI firmware bug
- Added Airflow Temperature (0xBE) support
- Updated language files

ATI Catalyst™ 10.12 WHQL

Build info:
8.801-101125a-109589C-ATI
DriverVer=11/25/2010, 8.801.0.0000

[SolidBladez]

Re: Latest Overclocking Programs, System Info, Benchmarking, & Stability Tools

AMD Catalyst 10.12

Guru3D.com Forums - View Single Post - AMD Catalyst 10.12

[wazza300]

Re: Latest Overclocking Programs, System Info, Benchmarking, & Stability Tools

lets hope they've fixed the idle clocks for 5000 series or else itll be back to 10.10 drivers for me

[stasio]

Re: Latest Overclocking Programs, System Info, Benchmarking, & Stability Tools

ATi Catalyst 10.12 CCC2 Preview-Catalyst Control Center 2

Vista/Vista x64

http://www2.ati.com/DRIVERS/Catalyst_10.12_CCC2_Preview_Vista_Dec7.exe

Win7/7 x64

http://www2.ati.com/DRIVERS/Catalyst_10.12_CCC2_Preview_Win7_Dec7.exe

System Information Viewer 4.15

Added reporting of Intel Rapid Storage Technology RAID Sets and Drives including disk temperature reporting.
Added support for the On Semiconductor ASP0800 power controller to report the CPU Voltage, Current and Power usage. Added all three to the H/W Status panel and display of the Power on the initial screen.
Added real-time DIMM Temperature reporting for Crucial Ballistix Finned DDR3 Memory Modules with Thermal Sensors.
Added support for the VIA Nano Dual-Core processor and also for the Intel HM55 chipset.

[PalZer0]

Re: Latest Overclocking Programs, System Info, Benchmarking, & Stability Tools

I can't find the release notes on AMD's website. Dunno what's going on there.

[stasio]

Re: Latest Overclocking Programs, System Info, Benchmarking, & Stability Tools

I can't find the release notes on AMD's website. Dunno what's going on there.

AMD Catalyst
Application Profiles:

http://downloads.guru3d.com/ATI-CrossFireX-Application-profiles-10.12-download-2501.html

Updated with:

JMicron SATA2 Driver 1.17.62 WHQL

a. Support IDE mode installation in driver package.
b. Support to get disk status under RAID mode for Hard Disk Sentinel.
c. Modify to check LBA access boundary to avoid device error.
d. Fix the issue taht S3 resume fails on OCZ Vertex-turbo SSD (OS disk) for JMB36X C.
e. Fix the issue that driver can not be installed on 64-bit French-version OS.
f. Fix the issue that silent installation fails on CD.

HWiNFO32 3.62.1049 Beta

* Enhanced support of ATI PM2 sensors.
* Added support of CHiL CH8266 PWM (for monitoring of GPU voltage, current, power).
* Added universal support of CSMI SAS (improved drive detection).
* Enhanced sensor monitoring on ASUS Rampage III GENE/Extreme.
* Enhanced support of AMD Family 15h.
* Added support of Intel XTU v2.1.
* Added nVidia GeForce GTX 570.
* Enhanced sensor monitoring on Intel 6-series desktop boards.
* Added nVidia GeForce GT 540M.
* Enhanced support of Ivy Bridge-DT/MB.
* Added preliminary support of Ivy Bridge-EP/EX (Ivytown).
* Enhanced sensor monitoring on MSI GX620.

[wazza300]

Re: Latest Overclocking Programs, System Info, Benchmarking, & Stability Tools

10.12 ati drivers still dont downclock the gpu to 157mhz core and 300mhz memory,havnt tried the 10.12 ccc preview yet

COME ON ATI SORT IT OUT !!!!! EDIT: i take back that comment,you need to load defaults in amd overdrive section,then it shows the correct idle clocks

i didnt overclock the card in anyway so i thought it would work after updating drivers but i had to load defaults after updating,makes sense really

hope this helps anyone else

[stasio]

Re: Latest Overclocking Programs, System Info, Benchmarking, & Stability Tools

Updated with:

Nec/Renesas USB 3.0 drivers Version 3.0.2.7.0.8

- Added the workaround of "xHCI Driver yellow bang problem".

[NуроFеn]

Re: Latest Overclocking Programs, System Info, Benchmarking, & Stability Tools

stasio, You can direct link Realtek Lan Driver-7.033 1125.2010 (Win 7 32/64) ?

[wazza300]

Re: Latest Overclocking Programs, System Info, Benchmarking, & Stability Tools

stasio, You can direct link Realtek Lan Driver-7.033 1125.2010 (Win 7 32/64) ?

there at the first page of this thread,all the latest motherboard drivers/utilities ect heres the realtek drivers

try here

http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=24&PFid=24&Level=4&Conn=3&DownTypeID=3&GetDown=false

click on the top one where it says "go"

[stasio]

Re: Latest Overclocking Programs, System Info, Benchmarking, & Stability Tools

stasio, You can direct link Realtek Lan Driver-7.033 1125.2010 (Win 7 32/64) ?

Done!
They sometime change destination.

try here

http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=24&PFid=24&Level=4&Conn=3&DownTypeID=3&GetDown=false

click on the top one where it says "go"

There are Realtek Lan Driver-7.031

[NуроFеn]

Re: Latest Overclocking Programs, System Info, Benchmarking, & Stability Tools

stasio

Done!

Thank you very much!

[stasio]

Re: Latest Overclocking Programs, System Info, Benchmarking, & Stability Tools

ATI Catalyst 10.12a Hotfix

https://a248.e.akamai.net/f/674/20307/1m/www2.ati.com/drivers/hotfix/cayman_press/amd_catalyst_win7_vista_8.79.6.2rc2_dec9.exe

AMD Catalyst

Updated with:

CrystalDiskInfo v3.9.4a

Improved workaround for SAMSUNG HD155UI/HD204UI firmware bug [3.9.4] Added workaround for SAMSUNG HD155UI/HD204UI firmware bug, Added Airflow Temperature (0xBE) support, Updated language files.

SetFSB 2.3.161.126

Added ICS9LPRS480BKL(Gateway NV53).
Added "ExoPC Slate"(ExoPC Slate).
Fixed "ASUS G73JH"(ASUS G53JW).
Included ASUS 1501P(ICS9LPR427AGLF).