ep43-ds3l memory divider problem

[Hackcremo]

hye.as i mention in title above..i purchased this mobo on new year eve..so it is a bit new, before this i can change the memory divider in bios without faced the on off on problem..but today when i want to change it, it happen..
when i press power button, it will run on(about 3 sec), then off then it will on again and run normally..however if i set it back to AUTO, this problem do not appear..i am using 2G kingston value ram..click below link to watch on off on problem...is it my mobo or ram fault??

on off on problem

[Hackcremo]

Re: ep43-ds3l memory divider problem

any1??

[Hackcremo]

Re: ep43-ds3l memory divider problem

update*

just clear cmos..
reformat my xp..
change ram slot from slot 1 to 2..
increase ram vdimm to 1.9v

but when change the memory multiplier, that problem happen again...

[Lsdmeasap]

Re: ep43-ds3l memory divider problem

Please link your ram and tell us if you are using a 2GB stick, or 2x1GB. And then so we are sure please post your exact settings you are trying that fail and we will advise back >>>>

Likely you are just using a incorrect multi/strap choice

This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

[b][u]MB Intelligent Tweaker(M.I.T.)[/u][/b]
Robust Graphics Booster ...............: Auto or Fast
CPU Clock Ratio ..........................: 
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 


[b][u]Clock Chip Control [/u][/b]
[b][u]Standard Clock Control[/u][/b]
CPU Host Clock Control..................: [Enabled] 
CPU Host Frequency (Mhz) ............: Mhz
[B]PCI Express Frequency (Mhz) .........:Set to 100[/B]

C.I.A.2 .................................:[Disabled]


[b][u]Advanced Clock Control [Press Enter][/u][/b]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 
MCH Clock Skew (ps)...................: <<< 


[b][u]DRAM Performance Control[/u][/b][u][/u]
[B]Performance Enhance...................: [STANDARD][/B]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 
Memory Frequency (Mhz) ..............: 
DRAM Timing Selectable ................: [Manual]

[b]Standard Timing Control[/b]
CAS Latency Time........................
tRCD .........................................
tRP'...........................................
tRAS..........................................

Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go

[b][u]Advanced Timing Control[/u][/b]
tRRD...........................................
tWTR..........................................
tWR............................................
tRFC...........................................
tRTP...........................................
Command Rate (CMD) ....................:2

[u][b]Driving Strength Profiles[/b][/u][b][/b]
Driving Strength ............................

[b]Channel A[/b]
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
 tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

[b]Channel B[/b]
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
 tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

[b][U]Motherboard Voltage Control[/U][/b][U][/U]
Voltage Type.………... Manual
[b]CPU[/b]
CPU Vcore….……….........................:
CPU Termination…..... 1.200V*.......: <<< Leave
CPU PLL…………………....1.500V*.......: << Please set to stock, Auto overvolts this way to much

CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 

CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly 

[b]MCH/ICH[/b]
MCH Core…………….....1.100V...........: << 
MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.550V............: <<< Leave
ICH Core…………...……1.100V............: <<< Leave

[b]DRAM[/b]
DRAM Voltage ……....1.800V............: 
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

[b][U]Advanced Settings[/U][/b][U][/U]
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

[b][U]Integrated Peripherals[/U][/b][U][/U]
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

[Hackcremo]

Re: ep43-ds3l memory divider problem

http://www.valueram.com/datasheets/KVR800D2N5_2G.pdf

using 2Gx1...

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................:12
Fine CPU Clock Ratio.....................:0.5
CPU Frequency ...........................:12.5x250 = 3125.2Mhz


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............:250 Mhz
PCI Express Frequency (Mhz) .........: 100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: AUTO
PCI Express Clock Drive.................: AUTO
CPU Clock Skew (ps)....................: AUTO
MCH Clock Skew (ps)...................: AUTO


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.0D
Memory Frequency (Mhz) ..............: 800 500
DRAM Timing Selectable ................: [AUTO]

Standard Timing Control
CAS Latency Time........................
tRCD .........................................
tRP'...........................................
tRAS..........................................

Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go

Advanced Timing Control
tRRD...........................................
tWTR..........................................
tWR............................................
tRFC...........................................
tRTP...........................................
Command Rate (CMD) ....................:

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................:1.2V
CPU Termination…..... 1.200V*.......: AUTO
CPU PLL…………………....1.500V*.......: AUTO

CPU Referen.…………....0.755V*.......: AUTO

CPU Reference2………,,0.800V*.......:AUTO

MCH/ICH
MCH Core…………….....1.100V...........: << AUTO
MCH Reference….…….0.800V...........; <<< AUTO
MCH/DRAM Ref.…......0.900V...........: <<< AUTO
ICH I/O……………….....1.550V............: <<< AUTO
ICH Core…………...……1.100V............: <<< AUTO

DRAM
DRAM Voltage ……....1.800V............: 1.8V
DRAM Termination .…0.900V............: <<< AUTO
Channel A Reference 0.900V............: <<< AUTO
Channel B Reference 0.900V............: <<< AUTO
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB