![Ponder](https://www.tweaktownforum.com/core/images/smilies/ponder.gif)
<?xml:namespace prefix = o ns = "urn:schemas-microsoft-com:office:office" /><o:p></o:p>
System
E8400 cpu
PVS24G6400LLK ram
Evga 8500 video
Thanks
pwester
[b][u]MB Intelligent Tweaker(M.I.T.)[/u][/b] Robust Graphics Booster ...............: Auto or Fast CPU Clock Ratio ..........................: 9 Fine CPU Clock Ratio.....................:.0 CPU Frequency ...........................: 3.0 [b][u]Clock Chip Control [/u][/b] [b][u]Standard Clock Control[/u][/b] CPU Host Clock Control..................: [Enabled] CPU Host Frequency (Mhz) ............: 333Mhz [B]PCI Express Frequency (Mhz) .........:Set to 100[/B] C.I.A.2 .................................:[Disabled] [b][u]Advanced Clock Control [Press Enter][/u][/b] CPU Clock Drive...........................: <<< 800 PCI Express Clock Drive.................: <<< 900 CPU Clock Skew (ps)....................: <<< MCH Clock Skew (ps)...................: <<< [b][u]DRAM Performance Control[/u][/b][u][/u] [B]Performance Enhance...................: [STANDARD][/B] Extreme Memory Profile (X.M.P.).....: Disabled (G)MCH Frequency Latch...............: [Auto] System Memory Multiplier ..............: 2.40B Memory Frequency (Mhz) ..............: 800 DRAM Timing Selectable ................: [Manual] [b]Standard Timing Control[/b] CAS Latency Time........................4 tRCD .........................................4 tRP'...........................................4 tRAS..........................................12 Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go [b][u]Advanced Timing Control[/u][/b] tRRD...........................................3-4 tWTR..........................................3-6 tWR............................................4-6 tRFC...........................................52-62 tRTP...........................................3-5 Command Rate (CMD) ....................:2 [u][b]Driving Strength Profiles[/b][/u][b][/b] Driving Strength ............................800/1066 (Benchmark/Test both, set 800 now. I do find 1066 works better at 900, so you may want to try it first with 800) [b]Channel A[/b] Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well tRD Phase1 Adjustment...................:Auto tRD Phase2 Adjustment .................:Auto tRD Phase3 Adjustment..................:Auto Trd2rd(Different Rank)....................:Auto Twr2wr(Different Rank)...................:Auto Twr2rd(Different Rank)...................:Auto Trd2wr(Same/Diff Rank)..................:Auto Dimm1 Clock Skew Control...............:Auto ps Dimm2 Clock Skew Control...............:Auto ps [b]Channel B[/b] Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well tRD Phase1 Adjustment...................:Auto tRD Phase2 Adjustment .................:Auto tRD Phase3 Adjustment..................:Auto Trd2rd(Different Rank)....................:Auto Twr2wr(Different Rank)...................:Auto Twr2rd(Different Rank)...................:Auto Trd2wr(Same/Diff Rank)..................:Auto Dimm1 Clock Skew Control...............:Auto ps Dimm2 Clock Skew Control...............:Auto ps [b][U]Motherboard Voltage Control[/U][/b][U][/U] Voltage Type.………... Manual [b]CPU[/b] CPU Vcore….……….........................: Auto if not overclocking, if you are overclocking please find and set your own voltages CPU Termination…..... 1.200V*.......: <<< If overclocking at all please find and set your own voltage, at stock Auto it fine. If overclocking 1.2-1.34 should be good for most normal clocks CPU PLL…………………....1.500V*.......: << If overclocking at all Please set to stock, Auto overvolts this way to much. 1.5-1.6 CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly [b]MCH/ICH[/b] MCH Core…………….....1.100V...........: << 1.2-1.24 MCH Reference….…….0.800V...........; <<< Leave MCH/DRAM Ref.…......0.900V...........: <<< Leave ICH I/O……………….....1.550V............: <<< 1.55 ICH Core…………...……1.100V............: <<< 1.14-1.2 [b]DRAM[/b] DRAM Voltage ……....1.800V............: 2.0-2.1 DRAM Termination .…0.900V............: <<< Leave Channel A Reference 0.900V............: <<< Leave Channel B Reference 0.900V............: <<< Leave [b][U]Advanced Settings[/U][/b][U][/U] Limit CPUID Max. to 3.....................: [Disabled] No-Execute Memory Protect............: [Enabled] CPU Enhanced Halt (C1E)................: [Disabled] C2/C2E State Support....................: [Disabled] x C4/C4E State Support..................: [Disabled] CPU Thermal Monitor 2(TM2) ...........: [Enabled] CPU EIST Function.........................: [Disabled] Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC [b][U]Integrated Peripherals[/U][/b][U][/U] Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB
Comment