I m using EP45-DS3R with E8400 with 3 x 1Gb kingston windows vista ultimate 32bits it s working fine, the problem is when I try to shutdown the pc , it shutdowns and reboots. when I did that from windows or manualy( because even if I hold power botton during bios start up it reboot)..it never shutdown by it self. I have to turn off the power. I tried to resolve the problem, by , changing PSU, the RAM , I flash the bios with F7, F9, F10 , and nothing. -EP45-DS3R Rev1.0 F10 -CPU E8400 C0 -3 x DDR2-SDRAM PC2-5300(333 mhz) no overcloking really I need help. any ideas ? thanks guys.
Announcement
Collapse
No announcement yet.
EP45-DS3R can not shutdown
Collapse
X
-
Re: EP45-DS3R can not shutdown
Is this matching ram? Can you give me a link to it?
Put Performance Enhance on standard in the MIT Section of the BIOS and be sure to set your ram voltage.
I need the above info before I can best advise you though, but if you have not set those things already please do and see if it helps
Comment
-
Re: EP45-DS3R can not shutdown
Yes, please give us your full settings and we will advise back. >>>
This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours
Code:[b][u]MB Intelligent Tweaker(M.I.T.)[/u][/b] Robust Graphics Booster ...............: Auto or Fast CPU Clock Ratio ..........................: Fine CPU Clock Ratio.....................:.0 CPU Frequency ...........................: [b][u]Clock Chip Control [/u][/b] [b][u]Standard Clock Control[/u][/b] CPU Host Clock Control..................: [Enabled] CPU Host Frequency (Mhz) ............: Mhz [B]PCI Express Frequency (Mhz) .........:Set to 100[/B] C.I.A.2 .................................:[Disabled] [b][u]Advanced Clock Control [Press Enter][/u][/b] CPU Clock Drive...........................: <<< 800 PCI Express Clock Drive.................: <<< 900 CPU Clock Skew (ps)....................: <<< MCH Clock Skew (ps)...................: <<< [b][u]DRAM Performance Control[/u][/b][u][/u] [B]Performance Enhance...................: [STANDARD][/B] Extreme Memory Profile (X.M.P.).....: Disabled (G)MCH Frequency Latch...............: [Auto] System Memory Multiplier ..............: Memory Frequency (Mhz) ..............: DRAM Timing Selectable ................: [Manual] [b]Standard Timing Control[/b] CAS Latency Time........................ tRCD ......................................... tRP'........................................... tRAS.......................................... Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go [b][u]Advanced Timing Control[/u][/b] tRRD........................................... tWTR.......................................... tWR............................................ tRFC........................................... tRTP........................................... Command Rate (CMD) ....................:2 [u][b]Driving Strength Profiles[/b][/u][b][/b] Driving Strength ............................ [b]Channel A[/b] Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well tRD Phase1 Adjustment...................:Auto tRD Phase2 Adjustment .................:Auto tRD Phase3 Adjustment..................:Auto Trd2rd(Different Rank)....................:Auto Twr2wr(Different Rank)...................:Auto Twr2rd(Different Rank)...................:Auto Trd2wr(Same/Diff Rank)..................:Auto Dimm1 Clock Skew Control...............:Auto ps Dimm2 Clock Skew Control...............:Auto ps [b]Channel B[/b] Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well tRD Phase1 Adjustment...................:Auto tRD Phase2 Adjustment .................:Auto tRD Phase3 Adjustment..................:Auto Trd2rd(Different Rank)....................:Auto Twr2wr(Different Rank)...................:Auto Twr2rd(Different Rank)...................:Auto Trd2wr(Same/Diff Rank)..................:Auto Dimm1 Clock Skew Control...............:Auto ps Dimm2 Clock Skew Control...............:Auto ps [b][U]Motherboard Voltage Control[/U][/b][U][/U] Voltage Type.………... Manual [b]CPU[/b] CPU Vcore….……….........................: CPU Termination…..... 1.200V*.......: <<< Leave CPU PLL…………………....1.500V*.......: << Please set to stock, Auto overvolts this way to much CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly [b]MCH/ICH[/b] MCH Core…………….....1.100V...........: << MCH Reference….…….0.800V...........; <<< Leave MCH/DRAM Ref.…......0.900V...........: <<< Leave ICH I/O……………….....1.550V............: <<< Leave ICH Core…………...……1.100V............: <<< Leave [b]DRAM[/b] DRAM Voltage ……....1.800V............: DRAM Termination .…0.900V............: <<< Leave Channel A Reference 0.900V............: <<< Leave Channel B Reference 0.900V............: <<< Leave [b][U]Advanced Settings[/U][/b][U][/U] Limit CPUID Max. to 3.....................: [Disabled] No-Execute Memory Protect............: [Enabled] CPU Enhanced Halt (C1E)................: [Disabled] C2/C2E State Support....................: [Disabled] x C4/C4E State Support..................: [Disabled] CPU Thermal Monitor 2(TM2) ...........: [Enabled] CPU EIST Function.........................: [Disabled] Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC [b][U]Integrated Peripherals[/U][/b][U][/U] Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB
Comment
-
Re: EP45-DS3R can not shutdown
Originally posted by Lsdmeasap View PostYes, please give us your full settings and we will advise back. >>>
This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours
Code:[B][U]MB Intelligent Tweaker(M.I.T.)[/U][/B] Robust Graphics Booster ...............: Auto CPU Clock Ratio ..........................: 9x Fine CPU Clock Ratio.....................:.+0.0 CPU Frequency ...........................: 3.00 Ghz (333x9) [B][U]Clock Chip Control [/U][/B] [B][U]Standard Clock Control[/U][/B] CPU Host Clock Control..................: [Disabled] CPU Host Frequency (Mhz) ............: 333Mhz [B]PCI Express Frequency (Mhz) .........:auto[/B] C.I.A.2 .................................:[Disabled] [B][U]Advanced Clock Control [Press Enter][/U][/B] CPU Clock Drive...........................: <<< 800mV PCI Express Clock Drive.................: <<< 900mV CPU Clock Skew (ps)....................: <<< 0ps MCH Clock Skew (ps)...................: <<< 0ps [B][U]DRAM Performance Control[/U][/B] [B]Performance Enhance...................: [STANDARD][/B] Extreme Memory Profile (X.M.P.).....: I do not have this lie (G)MCH Frequency Latch...............: [Auto] System Memory Multiplier ..............: auto Memory Frequency (Mhz) ..............:667 DRAM Timing Selectable ................: [auto] [B]Standard Timing Control[/B] CAS Latency Time........................5 auto tRCD .........................................5 auto tRP'...........................................5 auto tRAS..........................................15 auto Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go===>> I can t change anything in the menu [B][U]Advanced Timing Control[/U][/B] tRRD...........................................3 auto tWTR..........................................3 auto tWR............................................5 auto tRFC...........................................36 auto tRTP...........................................3 auto Command Rate (CMD) ....................:0 auto [U][B]Driving Strength Profiles[/B][/U] Driving Strength ............................ [B]Channel A[/B] Static tRead Value.........................:9 auto tRD Phase0 Adjustment...................:0 Auto <<< Leave for all below as well tRD Phase1 Adjustment...................:0 Auto tRD Phase2 Adjustment .................: 0 Auto tRD Phase3 Adjustment..................: 0 Auto Trd2rd(Different Rank)....................:6 Auto Twr2wr(Different Rank)...................:6 Auto Twr2rd(Different Rank)...................:5 Auto Trd2wr(Same/Diff Rank)..................:8 Auto Dimm1 Clock Skew Control...............:Auto Dimm2 Clock Skew Control...............:Auto [B]Channel B[/B] Static tRead Value.........................:9 auto tRD Phase0 Adjustment...................:0 Auto <<< Leave for all below as well tRD Phase1 Adjustment...................:0 Auto tRD Phase2 Adjustment .................:0 Auto tRD Phase3 Adjustment..................:0Auto Trd2rd(Different Rank)....................:6 Auto Twr2wr(Different Rank)...................:6Auto Twr2rd(Different Rank)...................:5 Auto Trd2wr(Same/Diff Rank)..................:8Auto Dimm1 Clock Skew Control...............:Auto Dimm2 Clock Skew Control...............:Auto [B][U]Motherboard Voltage Control[/U][/B] Voltage Type.………... [B]CPU[/B] CPU Vcore….………1.22500V auto....................:auto CPU Termination…..... 1.200V*.......: auto CPU PLL…………………....1.500V*.......: auto CPU Referen.…………....0.760V*.......:auto I do not have this line ref2 : CPU Reference2………,,0.0V*.......:auto<<< .67% Of Vtt (Termination above) Auto Will set this correctly [B]MCH/ICH[/B] MCH Core…………….....1.100V...........:auto << MCH Reference….…….0.760V...........;auto MCH/DRAM Ref.…......0.900V...........: auto<<< Leave ICH I/O……………….....1.500V............: auto I do not have this line: ICH Core…………...……00V............: <<< Leave [B]DRAM[/B] DRAM Voltage ……....1.800V............: 1.800V DRAM Termination .…0.900V............: auto Channel A Reference 0.900V............: auto Channel B Reference 0.900V............: auto [B][U]Advanced Settings[/U][/B] Limit CPUID Max. to 3.....................: [Disabled] No-Execute Memory Protect............: [Enabled] CPU Enhanced Halt (C1E)................: [Enabled] C2/C2E State Support....................: [Disabled] x C4/C4E State Support..................: [Disabled] CPU Thermal Monitor 2(TM2) ...........: [Enabled] CPU EIST Function.........................: [Enabled] Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC [B][U]Integrated Peripherals[/U][/B] Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB
Last edited by yssf; 01-13-2009, 10:24 AM.
Comment
-
Re: EP45-DS3R can not shutdown
That is not suggested settings at all man, just a template for you to give me your settings back with that you are having issues with. You have to fill it in with your settings you are using and I will advise back
Comment
-
Re: EP45-DS3R can not shutdown
Originally posted by Lsdmeasap View PostThat is not suggested settings at all man, just a template for you to give me your settings back with that you are having issues with. You have to fill it in with your settings you are using and I will advise back
Comment
Comment