Announcement

**Ramman1269** · 01-06-2009, 02:35 AM

Re: GA-EP45-UD3P q6600 3.41 max OC? Current settings inside

Bump for LSD

**Lsdmeasap** · 01-06-2009, 03:39 AM

Re: GA-EP45-UD3P q6600 3.41 max OC? Current settings inside

Some Q6600 need more then 1.5 for 3.6, after 3.4/3.5 voltage normally needs larger jumps for sure to go up small amounts. So you may just need more then you or your cooling is wanting to accept. Good thing is 3.4-3.6 is not much of a difference. All up to you if you really want to pump voltages for .2Ghz. And with Quads at high clocks you may HAVE to adjust and find stable Ref voltages. Try .63% -.73% MCH Ref voltage, and Just so you know I also did mean find and set CPU Ref voltages as well nto just this. I just mentioned that ref as a starter. To do that you need to first know this info >>>

CPU Termination (Vtt) Automatically changes the following if manually set >>>

CPU Reference Voltage (.63% of Default Vtt/1.20)
CPU Reference2 Voltage (.67% of Default Vtt/1.20)
MCH Reference Voltage (.63% of Default Vtt/1.20)

DRAM Voltage Automatically changes the following if manually set >>>

MCH/DRAM Reference Voltage (.50% of Default Dram Voltage)
DRAM Termination Voltage (.50% of Default Dram Voltage)
Channel A Reference Voltage (.50% of Default Dram Voltage)
Channel B Reference Voltage (.50% of Default Dram Voltage)

If you want a higher or lower than stock % / Value for any of the above settings you will find it easier to set the Dram Voltage or Vtt back to stock (Or above or below to find and be able to choose alternate % Values), then adjust desired setting to the % / Value you wish to use.

Then once you have selected a % range you want to use for said setting then go back and raise your Vtt or Dram Voltage back to what you choose to use and the corresponding settings will self adjust

Try this for 3.6 >>>
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto or Fast
CPU Clock Ratio ..........................: 8
CPU Frequency ...........................: 3.6GHz

Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 450
PCI Express Frequency (Mhz) .........: 100

C.I.A.2 .................................:[Disabled]

Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................: 900
CPU Clock Skew (ps)....................: 0
MCH Clock Skew (ps)...................: 0

DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.00D Use D for now as it will be more stable
Memory Frequency (Mhz) ..............: 900
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................ 5
tRCD ......................................... 5
tRP'........................................... 5
tRAS.......................................... 18

Advanced Timing Control
tRRD........................................... 3
tWTR.......................................... 5
tWR............................................ 6
tRFC........................................... 54
tRTP........................................... 3
Command Rate (CMD) ....................:2

Driving Strength Profiles
Driving Strength ...........................1066

Channel A
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH << Use the D choices

tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH << use the D Choices

tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................: 1.492 (CPU-Z 1.456) << More, try setting 1.525 in the BIOS
CPU Termination…..... 1.200V*.......: 1.46 << Try less like 1.38 and then try more like 1.49-1.52

CPU PLL…………………....1.500V*.......: 1.59
CPU Referen.…………....0.760V*.......: 0.760 [Auto]

MCH/ICH
MCH Core…………….....1.100V...........: 1.28 << Try 1.22-1.24, if no luck try 1.34-1.38

MCH Reference….…….0.800V...........: [Auto]
MCH/DRAM Ref.…......0.900V...........: [Auto]
ICH I/O……………….....1.550V............: 1.590
ICH Core…………...……1.100V............: 1.300 << 1.2 should be good

DRAM
DRAM Voltage ……....1.800V............: 2.0-2.08
DRAM Termination .…0.900V............: [Auto]
Channel A Reference 0.900V............: [Auto]
Channel B Reference 0.900V............: [Auto]

Announcement

GA-EP45-UD3P q6600 3.41 max OC? Current settings inside

GA-EP45-UD3P q6600 3.41 max OC? Current settings inside

Comment

Comment