Gigabyte+Mushkin

[chupa]

Hi folks. Could sure use some help here. I'm in the process of building a new computer. Here's my setup:

Gigabyte GA-EP45-DS4
Intel Q6600
Mushkin XP 2*2GB Dual Kit DDR2 1066Mhz
Sapphire ATI HD4830

System is working fine but all parts are default, no-oc.
And I want to...
Q6600 @3,2Ghz (is it dangerous with stock fan?)
Mushkin XP @1066Mhz&5.5.5.15 (if possible. running at 5.7.7.24 now)

What is the best bios settings for these specs? Any help is appreciated.

And... Sory for my English.
Piece

[chupa]

Re: Gigabyte+Mushkin

Any idea?

[chupa]

Re: Gigabyte+Mushkin

[Lsdmeasap]

Re: Gigabyte+Mushkin

Not sure about 3.2 with a stock fan, might be pretty hot!

What Mushkin Model # do you have?

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto or Fast
CPU Clock Ratio ..........................: 8
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................:3.208


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 401Mhz
PCI Express Frequency (Mhz) .........:Set to 100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<<
MCH Clock Skew (ps)...................: <<<


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.66D
Memory Frequency (Mhz) ..............: 1066Mhz
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................15

Advanced Timing Control
tRRD...........................................3-4
tWTR..........................................3-5
tWR............................................4-6
tRFC...........................................52-62
tRTP...........................................3-5
Command Rate (CMD) ....................:2

Driving Strength Profiles
Driving Strength ............................800/1066/1200 (Test/Bench all Three last, set 1066 now)

Channel A
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................:1.35-1.46 (All up to your chip)

CPU Termination…..... 1.200V*.......: <<< 1.25-1.45
CPU PLL…………………....1.500V*.......: << 1.5-1.58

CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly

CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly

MCH/ICH
MCH Core…………….....1.100V...........: << 1.2-1.3 (1.22-1.26 likely good)
MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.550V............: <<< 1.5-1.6
ICH Core…………...……1.100V............: <<< 1.1x-1.2

DRAM
DRAM Voltage ……....1.800V............: 2.0-2.1
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

[chupa]

Re: Gigabyte+Mushkin

Thanks for reply.

Mushkin XP 2*2 DDR2 1066 996599

[chupa]

Re: Gigabyte+Mushkin

tRFC...........................................52-62
What does it mean? (52 or 62) or (...56,57,58...) wich one?
and
6/7-10 333/B MCH - 8/9-12 400/D MCH
i can't understand that...

[Lsdmeasap]

Re: Gigabyte+Mushkin

Post edited above per your ram

tRFC...........................................52-62
What does it mean? (52 or 62) or (...56,57,58...) wich one?
and
6/7-10 333/B MCH - 8/9-12 400/D MCH
i can't understand that...

That means just as I wrote it, all the advanced timings are ranges, start with the higher numbers and work your way down one at a time testing with Memtest86+ as you go >>>
Memtest86+

6/7-10 333/B MCH - 8/9-12 400/D MCH

^^ That means if you are using a Memory Multi with a B on it use 6-10, if you are using one with D on it use 8-12. Starting with the higher values of course. Do this setting first, before you start lowering your advanced timings

[chupa]

Re: Gigabyte+Mushkin

Post edited above per your ram


That means just as I wrote it, all the advanced timings are ranges, start with the higher numbers and work your way down one at a time testing with Memtest86+ as you go >>>
Memtest86+

6/7-10 333/B MCH - 8/9-12 400/D MCH

^^ That means if you are using a Memory Multi with a B on it use 6-10, if you are using one with D on it use 8-12. Starting with the higher values of course. Do this setting first, before you start lowering your advanced timings

You are my hero, thank you very much. I will try this settings at tonight.

[Lsdmeasap]

Re: Gigabyte+Mushkin

Anytime man, good luck and post back if you need more help