EP45-DS4P OCZ 1066 problems

[ryan200]

Re: EP45-DS4P OCZ 1066 problems

i have the ds3l ep43 i was never able to get my ocz 1066 to work dual channel because it would only work in the 2 first slots and because of that i could do single channel 1066 but found it was faster to go dual channel 800mhz (well it would work 1066 dual channel but with tons of memory errors if you tested it in memtest)

so i just use 800mhz dual channel without problems

[Lsdmeasap]

Re: EP45-DS4P OCZ 1066 problems

Memset is available here in our memory guide and in this thread with MANY other tools >>

http://forums.tweaktown.com/f69/intel-burn-test-27994/

What you need to do is keep your ram settings very loose until you have your CPU stable and where you want it. Then you can work on your ram. Running OCCT without your ram loose and not knowing if your CPU Settings are stable is just going to confuse things as you wont know what it causing errors. If your ram is passing 5-10 passes of memtest but OCCT/Prime/Orthos fails then you know you have some CPU/voltage issues.

[SpeedEuphoria]

Re: EP45-DS4P OCZ 1066 problems

Adding to what Lsdmeasap said.

Another good idea to narrow down what the issue is, would be to rune either "small fft" in prime or "CPU" in OCCT to test just the CPU. Or you can set it to "blend" or "mix" to test more ram if you know that the cpu is stable at your voltage settings.

[WhatTHE****]

Re: EP45-DS4P OCZ 1066 problems

Thanx for all your help everyone...

now i can complete memtest no errors with this settup but not OCCT CPU or ram test

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: [Fast]
CPU Clock Ratio ..........................: [9 X]
Fine CPU Clock Ratio.....................: [+0.5]
CPU Frequency ...........................: [3.16GHz( 333x9.5)]


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: [333] Mhz
PCI Express Frequency (Mhz) .........: [100]

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: [800mV]
PCI Express Clock Drive.................: [900mV]
CPU Clock Skew (ps)....................: [0ps]
MCH Clock Skew (ps)...................: [0]


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: [3.20ZB]
Memory Frequency (Mhz) ..............: 1066
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................ 5
tRCD .........................................[5]
tRP'...........................................[5]
tRAS..........................................[18]

Advanced Timing Control
tRRD...........................................4
tWTR..........................................4
tWR............................................8
tRFC...........................................64
tRTP...........................................4
Command Rate (CMD) ....................:2

Driving Strength Profiles
Driving Strength ............................800 would not complete memtest in 1066

Channel A
Static tRead Value.........................:8
tRD Phase0 Adjustment...................:0 Auto
tRD Phase1 Adjustment...................: 0 Auto
tRD Phase2 Adjustment .................: 0 Auto
tRD Phase3 Adjustment..................: 0 Auto
Trd2rd(Different Rank)....................:6 Auto
Twr2wr(Different Rank)...................:6 Auto
Twr2rd(Different Rank)...................:5 Auto
Trd2wr(Same/Diff Rank)..................: 8 Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:8
tRD Phase0 Adjustment...................:0 Auto
tRD Phase1 Adjustment...................:0 Auto
tRD Phase2 Adjustment .................:0 Auto
tRD Phase3 Adjustment..................:0 Auto
Trd2rd(Different Rank)....................:6 Auto
Twr2wr(Different Rank)...................:6 Auto
Twr2rd(Different Rank)...................:5 Auto
Trd2wr(Same/Diff Rank)..................:8 Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore.........................:1.25000V [1.25625V] would not complete memtest at 1.25V Auto
CPU Termination...... 1.200V*.......: 1.2000V [Auto]
CPU PLL.............1.500V*.......: 1.5000V [Auto]

CPU Referen.........0.755V*.......: 0.760V [Auto]
CPU Reference2...,,0.800V*.......:0.800V [Auto]

MCH/ICH
MCH Core..........1.100V...........: [Normal]
MCH Reference.....0.800V...........; 0.760V [Auto]
MCH/DRAM Ref........0.900V...........: 0.900V [Auto]
ICH I/O...........1.550V............: 1.500V [Auto] 1.5
ICH Core.........1.100V............: [1.140]
DRAM
DRAM Voltage ......1.800V............: [2.060V]
DRAM Termination ..0.900V............: 0.900V[auto]
Channel A Reference 0.900V............: 0.900V[Auto]
Channel B Reference 0.900V............: 0.900V[Auto]

[WhatTHE****]

Re: EP45-DS4P OCZ 1066 problems

No matter how lose my ram settings are I cant get stability, the above settings are the only ones that will get through memtest but still cant get OCCT to run with out errors and get BSOD randomly.