Tweet
Hey I have been looking around, this is my 1st Intel rig comming from old AMD socket 939 on a DFI board. I have been learning about the different terms like Vtt/PL, ect..
I have a UD3P, E8400(E0), 2x2GB OCZ 1066 platinum
I can do 3.6Ghz on low volts, but anytime I try and go higher it wont boot. I lower the multi and keep the memory at 1066 or I even tried 800 and it still wont boot. Its very strange, I tried giving more volts to everything and still nothing, so I have just been lowering volts on everything @3.6Ghz to see what my minimums are, lol.
The other thing that is crazy is when I look for Static tRead sometimes it will be 8, sometimes 6 sometimes 10, this is all with the same 400FSB, wth?? I have it manually set to 8 but have used memset to do 7
I have a UD3P, E8400(E0), 2x2GB OCZ 1066 platinum
Code:
[B][U]MB Intelligent Tweaker(M.I.T.)[/U][/B] Robust Graphics Booster ...............:Auto(others wont boot) CPU Clock Ratio ..........................: 9 Fine CPU Clock Ratio.....................:.0 CPU Frequency ...........................: 400x9 3600 [B][U]Clock Chip Control [/U][/B] [B][U]Standard Clock Control[/U][/B] CPU Host Clock Control..................: [Enabled] CPU Host Frequency (Mhz) ............: 400Mhz [B]PCI Express Frequency (Mhz) .........:100[/B] C.I.A.2 .................................:[Disabled] [B][U]Advanced Clock Control [Press Enter][/U][/B] CPU Clock Drive...........................: <<< PCI Express Clock Drive.................: <<< CPU Clock Skew (ps)....................: <<< MCH Clock Skew (ps)...................: <<< [B][U]DRAM Performance Control[/U][/B] [B]Performance Enhance...................: [STANDARD][/B] Extreme Memory Profile (X.M.P.).....: Disabled (G)MCH Frequency Latch...............: 400[Auto] System Memory Multiplier ..............: 2.66D Memory Frequency (Mhz) ..............: 1066 DRAM Timing Selectable ................: [Manual] [B]Standard Timing Control[/B] CAS Latency Time........................5 tRCD .........................................5 tRP'...........................................4 tRAS..........................................14 [B][U]Advanced Timing Control[/U][/B] tRRD...........................................Auto tWTR..........................................Auto tWR............................................Auto tRFC...........................................52 tRTP...........................................Auto Command Rate (CMD) ....................:2 [U][B]Driving Strength Profiles[/B][/U] Driving Strength ............................Auto [B]Channel A[/B] Static tRead Value.........................:8 tRD Phase0 Adjustment...................:Auto tRD Phase1 Adjustment...................:Auto tRD Phase2 Adjustment .................:Auto tRD Phase3 Adjustment..................:Auto Trd2rd(Different Rank)....................:Auto Twr2wr(Different Rank)...................:Auto Twr2rd(Different Rank)...................:Auto Trd2wr(Same/Diff Rank)..................:Auto Dimm1 Clock Skew Control...............:Auto ps Dimm2 Clock Skew Control...............:Auto ps [B]Channel B[/B] Static tRead Value.........................:8 tRD Phase0 Adjustment...................:Auto tRD Phase1 Adjustment...................:Auto tRD Phase2 Adjustment .................:Auto tRD Phase3 Adjustment..................:Auto Trd2rd(Different Rank)....................:Auto Twr2wr(Different Rank)...................:Auto Twr2rd(Different Rank)...................:Auto Trd2wr(Same/Diff Rank)..................:Auto Dimm1 Clock Skew Control...............:Auto ps Dimm2 Clock Skew Control...............:Auto ps [B][U]Motherboard Voltage Control[/U][/B] Voltage Type.………... Manual [B]CPU[/B] CPU Vcore….……….........................:1.200 CPU Termination…..... 1.200V*.......: 1.200 CPU PLL…………………....1.500V*.......: 1.500 CPU Referen.…………....0.755V*.......: Auto CPU Reference2………,,0.800V*.......:Auto [B]MCH/ICH[/B] MCH Core…………….....1.100V...........: 1.24 MCH Reference….…….0.800V...........; <<< Leave MCH/DRAM Ref.…......0.900V...........: <<< Leave ICH I/O……………….....1.550V............: <<< Leave ICH Core…………...……1.100V............: <<< Leave [B]DRAM[/B] DRAM Voltage ……....1.800V............: 2.10V DRAM Termination .…0.900V............: <<< Leave Channel A Reference 0.900V............: <<< Leave Channel B Reference 0.900V............: <<< Leave [B][U]Advanced Settings[/U][/B] Limit CPUID Max. to 3.....................: [Disabled] No-Execute Memory Protect............: [Enabled] CPU Enhanced Halt (C1E)................: [Disabled] C2/C2E State Support....................: [Disabled] x C4/C4E State Support..................: [Disabled] CPU Thermal Monitor 2(TM2) ...........: [Enabled] CPU EIST Function.........................: [Disabled] Virtualization Technology................: [Disabled] [B][U]Integrated Peripherals[/U][/B] Legacy USB Storage Detect ..............[Enabled]
The other thing that is crazy is when I look for Static tRead sometimes it will be 8, sometimes 6 sometimes 10, this is all with the same 400FSB, wth?? I have it manually set to 8 but have used memset to do 7
Comment