Announcement

**Lsdmeasap** · 12-06-2008, 02:20 AM

Re: Starting point for OC'ing GA-EP43-DS3L w/E8400

Hmm, well since you did not say what you want to try here is settings to try for 3.6 >>>

Code:

[b][u]MB Intelligent Tweaker(M.I.T.)[/u][/b]
Robust Graphics Booster ...............: Auto or Fast
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 3.618


[b][u]Clock Chip Control [/u][/b]
[b][u]Standard Clock Control[/u][/b]
CPU Host Clock Control..................: [Enabled] 
CPU Host Frequency (Mhz) ............: 402Mhz
[B]PCI Express Frequency (Mhz) .........:Set to 100[/B]

C.I.A.2 .................................:[Disabled]


[b][u]Advanced Clock Control [Press Enter][/u][/b]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 0-50
MCH Clock Skew (ps)...................: <<< 50-150


[b][u]DRAM Performance Control[/u][/b][u][/u]
[B]Performance Enhance...................: [STANDARD][/B]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.66D
Memory Frequency (Mhz) ..............: 1069
DRAM Timing Selectable ................: [Manual]

[b]Standard Timing Control[/b]
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................15/18

[b][u]Advanced Timing Control[/u][/b]
tRRD........................................... 3-4
tWTR..........................................3-6 (May need 12 ... See below comment)

tWR............................................4-6 (may need 14 first time you set, then go right to lower range)

tRFC...........................................52-62
tRTP...........................................3-5
Command Rate (CMD) ....................:2

[u][b]Driving Strength Profiles[/b][/u][b][/b]
Driving Strength ............................800-1066 Test both in a bench last, set 1066 now

[b]Channel A[/b]
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
 tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

[b]Channel B[/b]
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
 tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

[b][U]Motherboard Voltage Control[/U][/b][U][/U]
Voltage Type.………... Manual
[b]CPU[/b]
CPU Vcore….……….........................: All up to your chip, some can do 3.6 at stock set vcore manually but do not use AUTO.  Some will need more.  What you set here will not be what you get actual in windows (See CPU-z).  You may need 1.22-1.3 actual to do 3.6, just set high enough you get booted in and then you can slowly lower later

CPU Termination…..... 1.200V*.......: <<< 1.24-1.3 (Set below Vcore should be good)
CPU PLL…………………....1.500V*.......: << Please set to stock, Auto overvolts this way to much

CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 

CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly 

[b]MCH/ICH[/b]
MCH Core…………….....1.100V...........: << 1.2-1.3 (1.24-1.28 likely fine)
MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.550V............: <<< 1.55-1.6
ICH Core…………...……1.100V............: <<< 1.1x-1.2

[b]DRAM[/b]
DRAM Voltage ……....1.800V............: 2.0-2.1 (Check your ram sticker and set accordingly)
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

[b][U]Advanced Settings[/U][/b][U][/U]
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

[b][U]Integrated Peripherals[/U][/b][U][/U]
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

Announcement

Starting point for OC'ing GA-EP43-DS3L w/E8400

Starting point for OC'ing GA-EP43-DS3L w/E8400

Comment