Can someone please...

[takovr]

Can someone please post there "MB Tweaker" settings for a ga-ep45ds3r/ds3 motherboard and a intel 8500 cpu. I have my pc over-clocked to 4.1gigs but have been reading on this fourm that my voltage and cpu pll and cpu termination is set to high. I would like to post my settings but don't know how.

[Lsdmeasap]

Re: Can someone please...

Please post your full specs and then fill this in and post it back

You can print it out on paper and write what you have in the BIOS and come back and fill it in, or just take your own notes and come back and fill it in. No other way about it but manually doing it

This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

[b][u]MB Intelligent Tweaker(M.I.T.)[/u][/b]
Robust Graphics Booster ...............: 
CPU Clock Ratio ..........................: 
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 


[b][u]Clock Chip Control [/u][/b]
[b][u]Standard Clock Control[/u][/b]
CPU Host Clock Control..................: [Enabled] 
CPU Host Frequency (Mhz) ............: Mhz
[B]PCI Express Frequency (Mhz) .........:Set to 100[/B]

C.I.A.2 .................................:[Disabled]


[b][u]Advanced Clock Control [Press Enter][/u][/b]
CPU Clock Drive...........................: <<< 
PCI Express Clock Drive.................: <<< 
CPU Clock Skew (ps)....................: <<< 
MCH Clock Skew (ps)...................: <<< 


[b][u]DRAM Performance Control[/u][/b][u][/u]
[B]Performance Enhance...................: [STANDARD][/B]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 
Memory Frequency (Mhz) ..............: 
DRAM Timing Selectable ................: [Manual]

[b]Standard Timing Control[/b]
CAS Latency Time........................
tRCD .........................................
tRP'...........................................
tRAS..........................................

[b][u]Advanced Timing Control[/u][/b]
tRRD...........................................
tWTR..........................................
tWR............................................
tRFC...........................................
tRTP...........................................
Command Rate (CMD) ....................:2

[u][b]Driving Strength Profiles[/b][/u][b][/b]
Driving Strength ............................

[b]Channel A[/b]
Static tRead Value.........................:7-10
 tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

[b]Channel B[/b]
Static tRead Value.........................:7-10
 tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

[b][U]Motherboard Voltage Control[/U][/b][U][/U]
Voltage Type.………... Manual
[b]CPU[/b]
CPU Vcore….……….........................:
CPU Termination…..... 1.200V*.......: <<< Leave
CPU PLL…………………....1.500V*.......: << Please set to stock, Auto overvolts this way to much

CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 

CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly 

[b]MCH/ICH[/b]
MCH Core…………….....1.100V...........: << 
MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.550V............: <<< Leave
ICH Core…………...……1.100V............: <<< Leave

[b]DRAM[/b]
DRAM Voltage ……....1.800V............: 
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

[b][U]Advanced Settings[/U][/b][U][/U]
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

[b][U]Integrated Peripherals[/U][/b][U][/U]
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB