GA-EP45-DS4P overclocking request

[linderman]

Hello:

being a gigabyte freak; I am thrilled to no end to find this forum!


I have my board overclocked to 3.8 ghz with 2 x 2 gigs Corsair Dominator 1066mhz ram

ultra 120 extreme cooler

cant seem to get any higher ...... want 4.0ghz

could you please post the settings I can try ........ I have the F8 bios and its been set to load optimized defaults and then manually adjusted

thanks

[Lsdmeasap]

Re: GA-EP45-DS4P overclocking request

Please post your CPU and a link to your exact ram if you can please. Then fill this out with what you are using for 3.8 and I will try to help you get 4Ghz. >>>>

This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

[b][u]MB Intelligent Tweaker(M.I.T.)[/u][/b]
Robust Graphics Booster ...............: 
CPU Clock Ratio ..........................: 
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 


[b][u]Clock Chip Control [/u][/b]
[b][u]Standard Clock Control[/u][/b]
CPU Host Clock Control..................: [Enabled] 
CPU Host Frequency (Mhz) ............: Mhz
[B]PCI Express Frequency (Mhz) .........:Set to 100[/B]

C.I.A.2 .................................:[Disabled]


[b][u]Advanced Clock Control [Press Enter][/u][/b]
CPU Clock Drive...........................: <<< 
PCI Express Clock Drive.................: <<< 
CPU Clock Skew (ps)....................: <<< 
MCH Clock Skew (ps)...................: <<< 


[b][u]DRAM Performance Control[/u][/b][u][/u]
[B]Performance Enhance...................: [STANDARD][/B]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 
Memory Frequency (Mhz) ..............: 
DRAM Timing Selectable ................: [Manual]

[b]Standard Timing Control[/b]
CAS Latency Time........................
tRCD .........................................
tRP'...........................................
tRAS..........................................

[b][u]Advanced Timing Control[/u][/b]
tRRD...........................................
tWTR..........................................
tWR............................................
tRFC...........................................
tRTP...........................................
Command Rate (CMD) ....................:2

[u][b]Driving Strength Profiles[/b][/u][b][/b]
Driving Strength ............................

[b]Channel A[/b]
Static tRead Value.........................:7-10
 tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

[b]Channel B[/b]
Static tRead Value.........................:7-10
 tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

[b][U]Motherboard Voltage Control[/U][/b][U][/U]
Voltage Type.………... Manual
[b]CPU[/b]
CPU Vcore….……….........................:
CPU Termination…..... 1.200V*.......: <<< Leave
CPU PLL…………………....1.500V*.......: << Please set to stock, Auto overvolts this way to much

CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 

CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly 

[b]MCH/ICH[/b]
MCH Core…………….....1.100V...........: << 
MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.550V............: <<< Leave
ICH Core…………...……1.100V............: <<< Leave

DRAM
DRAM Voltage ……....1.800V............: 
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

[b][U]Advanced Settings[/U][/b][U][/U]
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

[b][U]Integrated Peripherals[/U][/b][U][/U]
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

[linderman]

Re: GA-EP45-DS4P overclocking request

no CPU ............... DOH ....... sorry .... brain dead today

E8400

here is ram

Newegg.com - CORSAIR DOMINATOR 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 1066 (PC2 8500) Dual Channel Kit Desktop Memory - Desktop Memory


filling out OC settings now

[linderman]

Re: GA-EP45-DS4P overclocking request

not sure how to use the template

only settings I am changing in MIT is

cpu host = 430 mhz

Performance = Turbo

memory = 2.00 D

ram is 5-5-5-15

voltages are stock

[Lsdmeasap]

Re: GA-EP45-DS4P overclocking request

Ok! Copy/Paste is how you fill out that template. Your performance enhance setting is what it holding you back. You will have to use 900 Ram speed or 2.66D for 1197, I will post for 900 now. Or you could use 8x500 and 2.00D for 1000

Try this for 4Ghz >>>>

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto or Fast
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 4.05ghz


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 450Mhz
PCI Express Frequency (Mhz) .........:Set to 100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 50
MCH Clock Skew (ps)...................: <<< 150


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.00D
Memory Frequency (Mhz) ..............: 900
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................5
tRCD .........................................4/5
tRP'...........................................4/5
tRAS..........................................12/15


^^^ Since you are using less the stock speed @900, you may be able to use 544-12 or 544-15 ^^^

Use all highest values first below, then later you can lower one at a time testing as you go with memtest86+

Advanced Timing Control
tRRD...........................................3-4
tWTR..........................................3-6 (Set 12 first, then after you boot thru you can go right to the lower range)

tWR............................................ 4-6 (Set 14 first, then after you boot thru you can go right to the lower range)

tRFC...........................................52-62