Gigabyte UD3P + Intel E7200 + DDR2 800

[JPB]

Re: Gigabyte UD3P + Intel E7200 + DDR2 800

Here are some of my settings. I only copied the most important ones I think. If you need any others let me know and ill get them here asap.

MY SETTINGS ARE IN BOLD LETTERS




MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: AUTO
CPU Clock Ratio ..........................: 9X
Fine CPU Clock Ratio.....................: +0.5
CPU Frequency ...........................: 2.53 (266x9.5)


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [DISABLED]
CPU Host Frequency (Mhz) ............: 266 Mhz
PCI Express Frequency (Mhz) .........: AUTO

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<<
PCI Express Clock Drive.................: <<<
CPU Clock Skew (ps)....................: <<<
MCH Clock Skew (ps)...................: <<<


DRAM Performance Control
Performance Enhance...................: [TURBO]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: SPD (AUTO)
Memory Frequency (Mhz) ..............: 800
DRAM Timing Selectable ................: SPD (AUTO)

Standard Timing Control
CAS Latency Time........................ 5 AUTO
tRCD ......................................... 5 AUTO
tRP'........................................... 5 AUTO
tRAS.......................................... 15 AUTO

Advanced Timing Control
tRRD........................................... 3 AUTO
tWTR.......................................... 3 AUTO
tWR............................................ 6 AUTO
tRFC........................................... 52 AUTO
tRTP........................................... 3 AUTO
Command Rate (CMD) ....................: 0 AUTO

Driving Strength Profiles
Driving Strength ............................

Channel A
Static tRead Value.........................: 5 AUTO
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................: 5 AUTO1.10000V AUTO1.100V AUTO 1.800V AUTO

[JPB]

Re: Gigabyte UD3P + Intel E7200 + DDR2 800

Above are all my settings. Those are the most important ones I think. :)

[Lsdmeasap]

Re: Gigabyte UD3P + Intel E7200 + DDR2 800

Try this for 3.6 then >>>

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: AUTO or fast
CPU Clock Ratio ..........................: 9X
Fine CPU Clock Ratio.....................: +0.5
CPU Frequency ...........................: 3.562 (375x9.5)


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [enabled]
CPU Host Frequency (Mhz) ............: 375 Mhz
PCI Express Frequency (Mhz) .........: 100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<<
MCH Clock Skew (ps)...................: <<< 50-150


DRAM Performance Control
Performance Enhance...................: [Standard]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.40B
Memory Frequency (Mhz) ..............: 900
DRAM Timing Selectable ................: Manual

Standard Timing Control
CAS Latency Time........................ 5
tRCD ......................................... 5
tRP'........................................... 5
tRAS.......................................... 15/18

Advanced Timing Control
tRRD........................................... 3-4
tWTR.......................................... 3-6
tWR............................................4-6
tRFC........................................... 52-62
tRTP........................................... 3-5
Command Rate (CMD) ....................: 2

Driving Strength Profiles
Driving Strength ............................800/1066

Channel A
Static tRead Value.........................: 6/7-10
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................: 6/7-10
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................: 1.3+ You will have to find your own voltage here all CPU's are different. Do not use auto, set high enough to for sure boot and then you can lower later. What you set will be less in windows check with CPU-z how much and keep that in mind. You may need 1.25-1.34 actual to get 3.6 or more. All up to your chip

CPU Termination…..... 1.200V*.......: <<< 1.24-1.36 (1.24-1.3 likely be good for 3.6)
CPU PLL…………………....1.500V*.......: << Please set to stock, Auto overvolts this way to much

CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly

CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly

MCH/ICH
MCH Core…………….....1.100V...........: 1.2-1.3 (1.24-1.28 will be good likely)
MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.550V............: <<< 1.55-1.6
ICH Core…………...……1.100V............: <<< 1.1x-1.2

DRAM
DRAM Voltage ……....1.800V............: 1.9-2.0

[JPB]

Re: Gigabyte UD3P + Intel E7200 + DDR2 800

Thanks. I am going to reboot now and run the settings you advised. I will let you know how it goes shortly.

If it does end up booting into Windows fine, what program should I use to ensure stability ?

[JPB]

Re: Gigabyte UD3P + Intel E7200 + DDR2 800

Ok, I changed all my settings to the ones above, and the PC rebooted and got stuck in a reboot mode.

My cpu vcore, I set it at 1.24v and all the other settings were exactly what you told me.

Do you think I need more vcore ?

Just to clarify....at stock idle my cpu temps are 21c with the Cooler Master Hyper 212

[Lsdmeasap]

Re: Gigabyte UD3P + Intel E7200 + DDR2 800

Ya, set to 1.35 or so that way you get at least 1.29-1.3 or so actual, then you can lower later. Use 1.32-1.34 Vtt as well for now

I use Memtest86+ for ram >>

http://www.memtest.org/#downiso

And Orthos For CPU/Ram stressing >>>

http://www.mediafire.com/?sgznjgggmij

But plenty of apps here (See Post #3) >>>

http://forums.tweaktown.com/f69/intel-burn-test-27994/

[JPB]

Re: Gigabyte UD3P + Intel E7200 + DDR2 800

I had to run out last evening and didn't get a chance to up the vcore. I am watching the Ravens/Redskins today :) and at the end of the game....

LET THE OVERCLOCKING BEGIN

I will post with results.

Thanks so far for all the information you have given me.

[Lsdmeasap]

Re: Gigabyte UD3P + Intel E7200 + DDR2 800

Good luck with your testing and let us know if you need some more help!

I need to find me some time to work on my 4.5Ghz profile!