[b][u]MB Intelligent Tweaker(M.I.T.)[/u][/b] Robust Graphics Booster ...............: Fast CPU Clock Ratio ..........................: 9 Fine CPU Clock Ratio.....................:.0 CPU Frequency ...........................: 3.00 [b][u]Clock Chip Control [/u][/b] [b][u]Standard Clock Control[/u][/b] CPU Host Clock Control..................: [Enabled] CPU Host Frequency (Mhz) ............: 333Mhz [B]PCI Express Frequency (Mhz) .........:Set to 100[/B] C.I.A.2 .................................:[Disabled] [b][u]Advanced Clock Control [Press Enter][/u][/b] CPU Clock Drive...........................: <<< stock PCI Express Clock Drive.................: <<< stock CPU Clock Skew (ps)....................: <<< 0-50 MCH Clock Skew (ps)...................: <<< 50-150 [b][u]DRAM Performance Control[/u][/b][u][/u] [B]Performance Enhance...................: [STANDARD][/B] Extreme Memory Profile (X.M.P.).....: Disabled (G)MCH Frequency Latch...............: [333] System Memory Multiplier ..............: 3.20 Memory Frequency (Mhz) ..............: 1066 DRAM Timing Selectable ................: [Manual] [b]Standard Timing Control[/b] CAS Latency Time........................5 tRCD .........................................5 tRP'...........................................5 tRAS..........................................15/18 [b][u]Advanced Timing Control[/u][/b] tRRD...........................................3-5 tWTR..........................................3-6 (May need 12 for first boot thru) tWR............................................4-6 (May need 14 for first boot thru) tRFC...........................................52-62 tRTP...........................................2-6 Command Rate (CMD) ....................:2 [u][b]Driving Strength Profiles[/b][/u][b][/b] Driving Strength ............................1066 or 1200 [b]Channel A[/b] Static tRead Value.........................:7-10 tRD Phase0 Adjustment...................:<<< Leave for all below as well tRD Phase1 Adjustment...................:Auto tRD Phase2 Adjustment .................:Auto tRD Phase3 Adjustment..................:Auto Trd2rd(Different Rank)....................:Auto Twr2wr(Different Rank)...................:Auto Twr2rd(Different Rank)...................:Auto Trd2wr(Same/Diff Rank)..................:Auto Dimm1 Clock Skew Control...............:Auto ps Dimm2 Clock Skew Control...............:Auto ps [b]Channel B[/b] Static tRead Value.........................:7-10 tRD Phase0 Adjustment...................:<<< Leave for all below as well tRD Phase1 Adjustment...................:Auto tRD Phase2 Adjustment .................:Auto tRD Phase3 Adjustment..................:Auto Trd2rd(Different Rank)....................:Auto Twr2wr(Different Rank)...................:Auto Twr2rd(Different Rank)...................:Auto Trd2wr(Same/Diff Rank)..................:Auto Dimm1 Clock Skew Control...............:Auto ps Dimm2 Clock Skew Control...............:Auto ps [b][U]Motherboard Voltage Control[/U][/b][U][/U] Voltage Type.………... Manual [b]CPU[/b] CPU Vcore….……….........................: All up to your chip, keep in mind what you set will be about .6 or so less actual voltage applied. So maybe 1.36-1.46 for a actual voltage of 1.3-1.4. And you may need more or less depending on how your chip acts. If you have used it before and know the voltage you used set it +.6. Main thing you want to do is set it high enough to boot for sure, you can lower it later CPU Termination…..... 1.200V*.......: <<< 1.25-1.45 CPU PLL…………………....1.500V*.......: <<< Set to what you see for stock CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) [b]MCH/ICH[/b] MCH Core…………….....1.100V...........: << 1.2-1.3 << Needed for 4GB MCH Reference….…….0.800V...........; <<< Leave MCH/DRAM Ref.…......0.900V...........: <<< Leave ICH I/O……………….....1.550V............: <<< Leave ICH Core…………...……1.100V............: <<< Leave DRAM DRAM Voltage ……....1.800V............: 2.0-2.1 (Check spec on ram sticker) DRAM Termination .…0.900V............: <<< Leave Channel A Reference 0.900V............: <<< Leave Channel B Reference 0.900V............: <<< Leave [b][U]Advanced Settings[/U][/b][U][/U] Limit CPUID Max. to 3.....................: [Disabled] No-Execute Memory Protect............: [Enabled] CPU Enhanced Halt (C1E)................: [Disabled] C2/C2E State Support....................: [Disabled] x C4/C4E State Support..................: [Disabled] CPU Thermal Monitor 2(TM2) ...........: [Enabled] CPU EIST Function.........................: [Disabled] Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC [b][U]Integrated Peripherals[/U][/b][U][/U] Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB
Tweet
Comment