[b][u]MB Intelligent Tweaker(M.I.T.)[/u][/b] Robust Graphics Booster ...............: Fast CPU Clock Ratio ..........................: 9 Fine CPU Clock Ratio.....................:.0 CPU Frequency ...........................: 4.05Ghz [b][u]Clock Chip Control [/u][/b] [b][u]Standard Clock Control[/u][/b] CPU Host Clock Control..................: [Enabled] CPU Host Frequency (Mhz) ............: 450Mhz [B]PCI Express Frequency (Mhz) .........:Set to 100[/B] C.I.A.2 .................................:[Disabled] [b][u]Advanced Clock Control [Press Enter][/u][/b] CPU Clock Drive...........................: <<< 800 PCI Express Clock Drive.................: <<< 900 CPU Clock Skew (ps)....................: <<< 50-100 MCH Clock Skew (ps)...................: <<< 100-150 [b][u]DRAM Performance Control[/u][/b][u][/u] [B]Performance Enhance...................: [STANDARD][/B] Extreme Memory Profile (X.M.P.).....: Disabled (G)MCH Frequency Latch...............: [400] << Set Voltages, and Static Tread high, and this only and save/reboot to make other changes. Main idea is to make as little changes as you can with this setting. If you have issues, set all other values high first then reboot and change this System Memory Multiplier ..............: 2.00 Memory Frequency (Mhz) ..............: 900 DRAM Timing Selectable ................: [Manual] [b]Standard Timing Control[/b] CAS Latency Time........................5 tRCD .........................................4/5 tRP'...........................................4/5 tRAS..........................................12/15 ^^^ I posted slower then stock speed for your ram, so you may be able to use tighter timings then stock, as noted above. If you do test these, do so with the below all still on highest (If you would rather me give you settings for 1066 speed ram, let me know and I will) Set to all highest below first, then later lower one by one testing as you go with memtest86+ [b][u]Advanced Timing Control[/u][/b] tRRD...........................................3-5 tWTR..........................................3-6 (may need 12 for first boot thru) tWR............................................4-6 (may need 14 for first boot thru) tRFC...........................................48/52-62 tRTP...........................................3-5 Command Rate (CMD) ....................:2 [u][b]Driving Strength Profiles[/b][/u][b][/b] Driving Strength ............................1066 or 1200, sometimes higher here is better [b]Channel A[/b] Static tRead Value.........................:8-10 tRD Phase0 Adjustment...................:<<< Leave for all below as well tRD Phase1 Adjustment...................:Auto tRD Phase2 Adjustment .................:Auto tRD Phase3 Adjustment..................:Auto Trd2rd(Different Rank)....................:Auto Twr2wr(Different Rank)...................:Auto Twr2rd(Different Rank)...................:Auto Trd2wr(Same/Diff Rank)..................:Auto Dimm1 Clock Skew Control...............:Auto ps Dimm2 Clock Skew Control...............:Auto ps [b]Channel B[/b] Static tRead Value.........................:8-10 tRD Phase0 Adjustment...................:<<< Leave for all below as well tRD Phase1 Adjustment...................:Auto tRD Phase2 Adjustment .................:Auto tRD Phase3 Adjustment..................:Auto Trd2rd(Different Rank)....................:Auto Twr2wr(Different Rank)...................:Auto Twr2rd(Different Rank)...................:Auto Trd2wr(Same/Diff Rank)..................:Auto Dimm1 Clock Skew Control...............:Auto ps Dimm2 Clock Skew Control...............:Auto ps [b][U]Motherboard Voltage Control[/U][/b][U][/U] Voltage Type.………... Manual [b]CPU[/b] CPU Vcore….……….........................: << All up to your chip, Keep in mind what you set here will be about .6 or so less actual Voltage applied. So maybe around 1.38 set in the BIOS for 1.32 actual. May take more, maybe less, it all depends on your chip CPU Termination…..... 1.200V*.......: <<< 1.2-1.36 CPU PLL…………………....1.500V*.......: <<< 1.5 CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) [b]MCH/ICH[/b] MCH Core…………….....1.100V...........: << 1.2-1.3 MCH Reference….…….0.800V...........; <<< Leave MCH/DRAM Ref.…......0.900V...........: <<< Leave ICH I/O……………….....1.550V............: <<< 1.55-1.6 ICH Core…………...……1.100V............: <<< 1.15-1.2 DRAM DRAM Voltage ……....1.800V............: 2.0-2.1 (Stock Spec is not always needed, or best so be sure to test lower voltages after you get stable) DRAM Termination .…0.900V............: <<< Leave Channel A Reference 0.900V............: <<< Leave Channel B Reference 0.900V............: <<< Leave [b][U]Advanced Settings[/U][/b][U][/U] Limit CPUID Max. to 3.....................: [Disabled] No-Execute Memory Protect............: [Enabled] CPU Enhanced Halt (C1E)................: [Disabled] C2/C2E State Support....................: [Disabled] x C4/C4E State Support..................: [Disabled] CPU Thermal Monitor 2(TM2) ...........: [Enabled] CPU EIST Function.........................: [Disabled] Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC [b][U]Integrated Peripherals[/U][/b][U][/U] Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB
Tweet
Comment