help with GA-EP43-DS3L and e2180

[darkcorsa]

this is my first post , can someone help me with the OC on my new board, i use to have a ASUS P5B Deluxe, and now i bought the GA-EP43-DS3L, so i dont now how to overclock this board, i`m not sure of the voltages or settings.

can some help me please.


in the asus P5B deluxe i get 3500mhz on my e2180 350mhz*10x








cya

[darkcorsa]

Re: help with GA-EP43-DS3L and e2180

someone???????

[Lsdmeasap]

Re: help with GA-EP43-DS3L and e2180

Please post your full system specs and I can better advise you. And A link to your Ram would be great as well.

You want to run at 3.5 then right? If so please also tell me the vcore you used in your old board too.

If you want, fill this in as well with what you have so far and I will post it back for you soon as you give me more info about your system >>>

This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............:
CPU Clock Ratio ..........................:
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................:


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: Mhz
PCI Express Frequency (Mhz) .........:Set to 100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<<
PCI Express Clock Drive.................: <<<
CPU Clock Skew (ps)....................: <<<
MCH Clock Skew (ps)...................: <<<


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............:
Memory Frequency (Mhz) ..............:
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................
tRCD .........................................
tRP'...........................................
tRAS..........................................

Advanced Timing Control
tRRD...........................................
tWTR..........................................
tWR............................................
tRFC...........................................
tRTP...........................................
Command Rate (CMD) ....................:2

Channel A
Static tRead Value.........................:7-10
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:7-10
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................:
CPU Termination…..... 1.200V*.......: <<< Leave
CPU PLL…………………....1.500V*.......: <<< Leave
CPU Referen.…………....0.755V*.......: <<< .61% Of Vtt (Termination above)
CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above)

MCH/ICH
MCH Core…………….....1.100V...........: <<
MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.550V............: <<< Leave
ICH Core…………...……1.100V............: <<< Leave

DRAM
DRAM Voltage ……....1.800V............:
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]

[darkcorsa]

Re: help with GA-EP43-DS3L and e2180

Please post your full system specs and I can better advise you. And A link to your Ram would be great as well.

You want to run at 3.5 then right? If so please also tell me the vcore you used in your old board too.

If you want, fill this in as well with what you have so far and I will post it back for you soon as you give me more info about your system >>>

This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............:
CPU Clock Ratio ..........................:
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................:


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: Mhz
PCI Express Frequency (Mhz) .........:Set to 100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<<
PCI Express Clock Drive.................: <<<
CPU Clock Skew (ps)....................: <<<
MCH Clock Skew (ps)...................: <<<


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............:
Memory Frequency (Mhz) ..............:
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................
tRCD .........................................
tRP'...........................................
tRAS..........................................

Advanced Timing Control
tRRD...........................................
tWTR..........................................
tWR............................................
tRFC...........................................
tRTP...........................................
Command Rate (CMD) ....................:2

Channel A
Static tRead Value.........................:7-10
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:7-10
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage ControlCPUMCH/ICHAdvanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]

thanks man, my full system specs are:

CPU: Intel Pentium Dual-Core E2180
MBD: Gigabyte EP43 DS3L
Cooler: CoolerMaster Hiper TX2 92mm 6HeatPipes
RAM: 2 Gb Ram Corsair TwinX XMS2 DDR2-800 @ 1000Mhz
GFX: Sapphire HD4850 512mb con mod de BIOS
HDD1: Samsung 7200rpm 160Gb SATA2 Maxtor 5400rpm 80Gb Ide
MONITOR: Samsung SyncMaster 932BW 19" LCD
POWER SUPPLIES: Thermaltake Purepower 600W


when i get my cpu to 3500mhz i use a 1.5CPU Vcore

what do you thing, i can get a 3600mhz oc 24/7??


thanks for helping me

[Lsdmeasap]

Re: help with GA-EP43-DS3L and e2180

Ram link please?

Ya, that CPU needs alot of volts, and 1.5 in the BIOS is onl,y about 1.44 or so in windows

Post me a ram link And I can better advise ram volts and speed/timings

[darkcorsa]

Re: help with GA-EP43-DS3L and e2180

Ram link please?

Ya, that CPU needs alot of volts, and 1.5 in the BIOS is onl,y about 1.44 or so in windows

Post me a ram link And I can better advise ram volts and speed/timings

my memos are:

http://www.corsair.com/_datasheets/TWIN2X2048-6400C4.pdf

<table class="border_r" cellpadding="0" cellspacing="0"><tbody><tr><td class="border_lb" style="padding-right: 3px;">TWIN2X2048-6400C4 </td> <td id="ctl00_ctl00_cpBody_cpBody_wgtProductTable_rptM emory_ctl04_td5" class="border_lb" style="padding-right: 2px; width: 55px;"> PC2-6400 </td> <td id="ctl00_ctl00_cpBody_cpBody_wgtProductTable_rptM emory_ctl04_td1" class="border_lb" style="padding-right: 2px;"> 2GB Kit </td> <td id="ctl00_ctl00_cpBody_cpBody_wgtProductTable_rptM emory_ctl04_td2" class="border_lb" style="padding-right: 2px;"> 4-4-4-12 </td> <td id="ctl00_ctl00_cpBody_cpBody_wgtProductTable_rptM emory_ctl04_td3" class="border_lb" style="padding-right: 2px;"> 240pin DIMM </td></tr></tbody></table>

[Lsdmeasap]

Re: help with GA-EP43-DS3L and e2180

Thanks!

Ok, try these settings for now for 3.5, then later I can help you try for 3.6 if your temps are ok. But 3.4 or 3.5 may be the best place to run your CPU if 3.5/3.6 is hot. I do see most people have to use 1.45-1.5 Actual for 3.3-3.5, so 3.6 may be too much to ask out of your CPU (Have you seen the B.S.E.L Pin mod? You might want to do that) >>>>

Also that ram may not run very stable at 100Mhz, so you may want to keep it under that, tighter timings like 444-12 at 800-850, 555-15 at 850-900/950


Using the 10 Multi for 3.5 with ram at 444-12 @ 840Mhz

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............:
CPU Clock Ratio ..........................: 10
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 3.5Ghz


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 350Mhz
PCI Express Frequency (Mhz) .........:Set to 100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<<
PCI Express Clock Drive.................: <<<
CPU Clock Skew (ps)....................: <<< 50-150
MCH Clock Skew (ps)...................: <<< 50-250


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [333]
System Memory Multiplier ..............: 2.40
Memory Frequency (Mhz) ..............: 840Mhz
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................4
tRCD .........................................4
tRP'...........................................4
tRAS..........................................12

Advanced Timing Control
tRRD...........................................3-4
tWTR..........................................3-6 (May need 8-12 to start)
tWR............................................4-6 (May need 8-14 to start)
tRFC...........................................38 (40-42)
tRTP...........................................3-6
Command Rate (CMD) ....................:2

Driving Strength Profiles
Driving Strength ............................ 800

Channel A
Static tRead Value.........................:7-10
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:7-10
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................: 1.45-1.55 (Remember what you set in the BIOS will be much lower in Windows with P43/45 board. 1.45 is about 1.39 in windows. So you may need more then you used to use

CPU Termination…..... 1.200V*.......: <<< 1.3-1.6
CPU PLL…………………....1.500V*.......: <<< 1.5-1.6
CPU Referen.…………....0.755V*.......: <<< .61% Of Vtt (Termination above)
CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above)

MCH/ICH
MCH Core…………….....1.100V...........: << 1.15
MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.550V............: <<< Leave
ICH Core…………...……1.100V............: <<< Leave

DRAM
DRAM Voltage ……....1.800V............: 2.1V
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]

Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

__________________________________________________ ____

Using the 9 Multi for 3.5 with ram at 555-15/18 @ 936Mhz

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............:
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 3.5


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 390Mhz
PCI Express Frequency (Mhz) .........:Set to 100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<<
PCI Express Clock Drive.................: <<<
CPU Clock Skew (ps)....................: <<< 50-150
MCH Clock Skew (ps)...................: <<< 50-250


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [333]
System Memory Multiplier ..............: 2.40
Memory Frequency (Mhz) ..............: 936
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................15/18

Advanced Timing Control
tRRD...........................................3-4
tWTR..........................................3-6 (May need 8-12 to start)
tWR............................................4-6 (May need 8-14 to start)
tRFC...........................................38 (40-42)
tRTP...........................................3-6
Command Rate (CMD) ....................:2

Driving Strength Profiles
Driving Strength ............................ 800 or 1066

Channel A
Static tRead Value.........................:7-10
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:7-10
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................:1.45-1.55 (Remember what you set in the BIOS will be much lower in Windows with P43/45 board. 1.45 is about 1.39 in windows. So you may need more then you used to use

CPU Termination…..... 1.200V*.......: <<< 1.3-1.6
CPU PLL…………………....1.500V*.......: <<< 1.5-1.6
CPU Referen.…………....0.755V*.......: <<< .61% Of Vtt (Termination above)
CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above)

MCH/ICH
MCH Core…………….....1.100V...........: << 1.5
MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.550V............: <<< Leave
ICH Core…………...……1.100V............: <<< Leave

DRAM
DRAM Voltage ……....1.800V............: 2.1V
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]

Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB