I have GA-X48-DS4 and have been tweeking the ram i have Mushkin XPS2-8500 the setting below post fine not problems 100% stabel but ram runs at strap 2.40b 5:6
Robust Graphics Booster___________ [Auto]
CPU Clock Ratio ____________ [8]
CPU Host Clock Control_ [Enabled]
CPU Host Frequency (MHz)__________ [450]
PCI Express Frequency (Mhz)_______ [100]
C.I.A. 2__________________________ [Disabled]
System Memory Multiplier (SPD)____ [2.40B] =1080MHz
DRAM Timing Selectable_______ SPD __ [Manual]
Performance Enhance = [Standard]
CAS Latency Time________________ 5
Dram RAS# to CAS# Delay_________ 5
Dram RAS# Precharge Delay_______5
Precharge Delay (tRAS)__________ 15
ACT to ACT Delay (tRRD)_________ 3
Rank Write to READ Delay________ 4
Write to Precharge Delay_________ 4
Refresh to ACT Delay______________ 48
Read to Precharge Delay__________ 3
Static tRead Value_______________7
Static tRead Phase Adjust________ AUTO
CPU/PCIEX Clock Driving Control [800mV]
CPU Clock Skew Control [normal]
GMCH Clock Skew Control [Normal]
System Voltage Control____ [Manual]
DDR2 OverVoltage Control__ [+0.300V]
FSB OverVoltage Control___ [+0.1V]
(G)MCH OverVoltage Control [+0.150V]
I have been trying to get ram to run 1:1 @900 but i can not get past BIOS post.Im not sure why i taking the ram down in speed and thought i would be able to tighting up timming and run 1:1 if any one can tell me why this seems so hard .I tried uping timming lowing voltages but just does not what to post @1:1 900 strap 2.00D
Was hoping to run at 5-5-4-13@900
Robust Graphics Booster___________ [Auto]
CPU Clock Ratio ____________ [8]
CPU Host Clock Control_ [Enabled]
CPU Host Frequency (MHz)__________ [450]
PCI Express Frequency (Mhz)_______ [100]
C.I.A. 2__________________________ [Disabled]
System Memory Multiplier (SPD)____ [2.40B] =1080MHz
DRAM Timing Selectable_______ SPD __ [Manual]
Performance Enhance = [Standard]
CAS Latency Time________________ 5
Dram RAS# to CAS# Delay_________ 5
Dram RAS# Precharge Delay_______5
Precharge Delay (tRAS)__________ 15
ACT to ACT Delay (tRRD)_________ 3
Rank Write to READ Delay________ 4
Write to Precharge Delay_________ 4
Refresh to ACT Delay______________ 48
Read to Precharge Delay__________ 3
Static tRead Value_______________7
Static tRead Phase Adjust________ AUTO
CPU/PCIEX Clock Driving Control [800mV]
CPU Clock Skew Control [normal]
GMCH Clock Skew Control [Normal]
System Voltage Control____ [Manual]
DDR2 OverVoltage Control__ [+0.300V]
FSB OverVoltage Control___ [+0.1V]
(G)MCH OverVoltage Control [+0.150V]
I have been trying to get ram to run 1:1 @900 but i can not get past BIOS post.Im not sure why i taking the ram down in speed and thought i would be able to tighting up timming and run 1:1 if any one can tell me why this seems so hard .I tried uping timming lowing voltages but just does not what to post @1:1 900 strap 2.00D
Was hoping to run at 5-5-4-13@900
Comment