alright, first I'll give you my computer specs:
So basically I am unable to get my computer to run with any sense of stability. I'm pretty sure it's coming down to memory timing/voltages because nothing else really makes sense.
Right now I have only 1 pair of memory in slots 1 + 3 on the motherboard attempting to get some stability with 4GB as a jumping off point. I searched around and found someone with my same mobo and memory and the settings they used HERE.Well, my computer still will not run for more than about 10 minutes without a big fat BSOD.
I'm beyond frustrated at this point. I've been dealing with this for days and can't seem to get it right, so any help would be GREATLY appreciated.
So here are the settings I'm currently using:
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: [Auto]
CPU Clock Ratio ..........................: 9 X
Fine CPU Clock Ratio.....................:.+0.5
CPU Frequency ...........................: 3.16GHz (333x9.5)
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Disabled]
CPU Host Frequency (Mhz) ............: 333
PCI Express Frequency (Mhz) .........: [100]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800mV
PCI Express Clock Drive.................: 900mV
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)...................: 0ps
DRAM Performance Control
Performance Enhance...................: [Standard]
Extreme Memory Profile (X.M.P.).....: [Disabled]
(G)MCH Frequency Latch...............: [333MHz]
System Memory Multiplier ..............: [3.2B]
Memory Frequency (Mhz) ..............: 1066 1066
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................5 5
tRCD .........................................7 5
tRP'...........................................7 5
tRAS..........................................20 18
Advanced Timing Control
tRRD...........................................4 [4]
tWTR..........................................4 [6]
tWR............................................8 [11]
tRFC...........................................72 [55]
tRTP...........................................4 [5]
Command Rate (CMD) ....................0 [2]
Channel A
Static tRead Value.........................:8 [Auto]
tRD Phase0 Adjustment...................:0 [Auto]
tRD Phase1 Adjustment...................:0 [Auto]
tRD Phase2 Adjustment .................:0 [Auto]
tRD Phase3 Adjustment..................:0 [Auto]
Trd2rd(Different Rank)....................:8 [Auto]
Twr2wr(Different Rank)...................:8 [Auto]
Twr2rd(Different Rank)...................:7 [Auto]
Trd2wr(Same/Diff Rank)..................:9 [Auto]
Dimm1 Clock Skew Control...............:[Auto]
Dimm2 Clock Skew Control...............:[Auto]
Channel B
Static tRead Value.........................:8 [Auto]
tRD Phase0 Adjustment...................:0 [Auto]
tRD Phase1 Adjustment...................:0 [Auto]
tRD Phase2 Adjustment .................:0 [Auto]
tRD Phase3 Adjustment..................:0 [Auto]
Trd2rd(Different Rank)....................:8 [Auto]
Twr2wr(Different Rank)...................:8 [Auto]
Twr2rd(Different Rank)...................:7 [Auto]
Trd2wr(Same/Diff Rank)..................:9 [Auto]
Dimm1 Clock Skew Control...............:[-500ps]
Dimm2 Clock Skew Control...............:[-400ps]
Motherboard Voltage ControlCPU1.22500V....: [Auto]1.200V.......: [Auto]1.500V.......: [Auto]0.760V.......: [Auto]
MCH/ICH1.100V...........: [1.300V]0.760V...........; [Auto]
0.900V...........: [Auto]1.500V............: [Auto]
DRAM.1.800V............: [2.100V]0.900V............: [Auto]
Channel A Reference 0.900V............: [Auto]
Channel B Reference 0.900V............: [Auto]
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Enabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled] GRAYED OUT
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Enabled]
Virtualization Technology................: [Enabled]
- Motherboard and revision: Gigabyte GA-EP45-DS3R v1.0
- BIOS: F10
- CPU: Intel C2D E8500 @ 3.16GHz
- Memory: OCZ Reaper HPC OCZ2RPR10664GK (I have 2 4GB kits)
- Video Card: Asus GeForce 9600GT
- Power Supply: Enermax Liberty 500W
- HDD: 2x Seagate 500GB in RAID0 config
- Optical Drives: 2x DVD+-RW DL
- Operating System: Vista Ultimate 64bit
So basically I am unable to get my computer to run with any sense of stability. I'm pretty sure it's coming down to memory timing/voltages because nothing else really makes sense.
Right now I have only 1 pair of memory in slots 1 + 3 on the motherboard attempting to get some stability with 4GB as a jumping off point. I searched around and found someone with my same mobo and memory and the settings they used HERE.Well, my computer still will not run for more than about 10 minutes without a big fat BSOD.
I'm beyond frustrated at this point. I've been dealing with this for days and can't seem to get it right, so any help would be GREATLY appreciated.
So here are the settings I'm currently using:
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: [Auto]
CPU Clock Ratio ..........................: 9 X
Fine CPU Clock Ratio.....................:.+0.5
CPU Frequency ...........................: 3.16GHz (333x9.5)
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Disabled]
CPU Host Frequency (Mhz) ............: 333
PCI Express Frequency (Mhz) .........: [100]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800mV
PCI Express Clock Drive.................: 900mV
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)...................: 0ps
DRAM Performance Control
Performance Enhance...................: [Standard]
Extreme Memory Profile (X.M.P.).....: [Disabled]
(G)MCH Frequency Latch...............: [333MHz]
System Memory Multiplier ..............: [3.2B]
Memory Frequency (Mhz) ..............: 1066 1066
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................5 5
tRCD .........................................7 5
tRP'...........................................7 5
tRAS..........................................20 18
Advanced Timing Control
tRRD...........................................4 [4]
tWTR..........................................4 [6]
tWR............................................8 [11]
tRFC...........................................72 [55]
tRTP...........................................4 [5]
Command Rate (CMD) ....................0 [2]
Channel A
Static tRead Value.........................:8 [Auto]
tRD Phase0 Adjustment...................:0 [Auto]
tRD Phase1 Adjustment...................:0 [Auto]
tRD Phase2 Adjustment .................:0 [Auto]
tRD Phase3 Adjustment..................:0 [Auto]
Trd2rd(Different Rank)....................:8 [Auto]
Twr2wr(Different Rank)...................:8 [Auto]
Twr2rd(Different Rank)...................:7 [Auto]
Trd2wr(Same/Diff Rank)..................:9 [Auto]
Dimm1 Clock Skew Control...............:[Auto]
Dimm2 Clock Skew Control...............:[Auto]
Channel B
Static tRead Value.........................:8 [Auto]
tRD Phase0 Adjustment...................:0 [Auto]
tRD Phase1 Adjustment...................:0 [Auto]
tRD Phase2 Adjustment .................:0 [Auto]
tRD Phase3 Adjustment..................:0 [Auto]
Trd2rd(Different Rank)....................:8 [Auto]
Twr2wr(Different Rank)...................:8 [Auto]
Twr2rd(Different Rank)...................:7 [Auto]
Trd2wr(Same/Diff Rank)..................:9 [Auto]
Dimm1 Clock Skew Control...............:[-500ps]
Dimm2 Clock Skew Control...............:[-400ps]
Motherboard Voltage ControlCPU1.22500V....: [Auto]1.200V.......: [Auto]1.500V.......: [Auto]0.760V.......: [Auto]
MCH/ICH1.100V...........: [1.300V]0.760V...........; [Auto]
0.900V...........: [Auto]1.500V............: [Auto]
DRAM.1.800V............: [2.100V]0.900V............: [Auto]
Channel A Reference 0.900V............: [Auto]
Channel B Reference 0.900V............: [Auto]
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Enabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled] GRAYED OUT
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Enabled]
Virtualization Technology................: [Enabled]
Comment