Asus Z68 V PRO 4.5GHZ Bios Screenshots

[ea3ot]

Re: Asus Z68 V PRO 4.5GHZ Bios Screenshots

Two screenshots of the RAm

1= 1866 (8-9-9-24 1t) vdram 1.50



2= 2133 (10-10-10-28 1t) vdram 1.55



Both pass SuperPi 100% ok

[wazza300]

Re: Asus Z68 V PRO 4.5GHZ Bios Screenshots

heres what i get at 1.625v dram and 2133mhz-9-10-10-28-1t



i think you would reach 2400mhz

[ea3ot]

Re: Asus Z68 V PRO 4.5GHZ Bios Screenshots

I have tested now 2133 at 9-10-10-28 1T with just 1.55V Vdram and is OK



SuperPi

[wazza300]

Re: Asus Z68 V PRO 4.5GHZ Bios Screenshots

it has to be your chip,mine just wont pass with anything less than 1.625v dram,i could loosen the timings and lower dram voltage but im not going to,try 2400mhz i know x79 cpu's can run that speed with 1.55v dram

you might need to run 10-10-10-28-2t at 2400mhz though,or 11-11-11-30-2t

[ea3ot]

Re: Asus Z68 V PRO 4.5GHZ Bios Screenshots

I think Wazza 1866 or 2133 make the job very well and as you see in the benchmarks the numbers are very close between. I will keep 1866 for 24/7 with only 1.50 v. beacouse 1.55 v at 2133 its almoust the same,

[wazza300]

Re: Asus Z68 V PRO 4.5GHZ Bios Screenshots

I think Wazza 1866 or 2133 make the job very well and as you see in the benchmarks the numbers are very close between. I will keep 1866 for 24/7 with only 1.50 v. beacouse 1.55 v at 2133 its almoust the same,

yes your right you can safely use upto 1.575 dram voltage though so dont be scared to use more,you have a better memory controller on 2700k chips i think,i cant run with those voltages at 2133mhz

[ea3ot]

Re: Asus Z68 V PRO 4.5GHZ Bios Screenshots

I keep at least temporary to check coldboots and stability the 2133 Mhz config, 9-10-10-28 1T with 1.55 vdram and for the moment seem very stable. Good coldboots and operation, let see in a few days..

[ea3ot]

Re: Asus Z68 V PRO 4.5GHZ Bios Screenshots

I must to say Wazza, after some period using this RAM,s Im more than happy. No more coldboot issues and using the kit at 2133mhz with 1.55 vdram and cant work any better.Nice, nice memorys.

[wazza300]

Re: Asus Z68 V PRO 4.5GHZ Bios Screenshots

yeah its good memory,they are cheap too,and very stable considering they are rated at 1600mhz

[ea3ot]

Re: Asus Z68 V PRO 4.5GHZ Bios Screenshots

You know what I did? I installed the Artic Cooler ( RC Pro) heatsinks ram coolers for this sticks. it really dont need but the aesthetics is much better,

[wazza300]

Re: Asus Z68 V PRO 4.5GHZ Bios Screenshots

do they make the ram taller? or just stick to the sides? its 30nm ram normal ram is 45nm so it runs cooler

[ea3ot]

Re: Asus Z68 V PRO 4.5GHZ Bios Screenshots

Yes you stick de RC plates individually to both sides of the RAM boards. Very easy to do. Is just a question of aesthetics.

http://www.youtube.com/watch?v=_-nTRs7sB7Q

[ea3ot]

Re: Asus Z68 V PRO 4.5GHZ Bios Screenshots

[wazza300]

Re: Asus Z68 V PRO 4.5GHZ Bios Screenshots

they look good,i needed mine to be low profile because of my d14 heatsink,but those look fine

[Tyreman]

Re: Asus Z68 V PRO 4.5GHZ Bios Screenshots

Heres a temp[late from mine P8Z68-V Pro/Gen 3
ymmv

Ripjaws ram in use here on below template

Now have swapped Ripjaws ram and running Samsung green 30nm tech ram and Oc'd it
Only change for ram settings Settings are
Ram volts 1.35
DDR3-1866
Timings: 9-9-9-24 1T
all other sub and tertiary timings auto



Bios 3202 Build Date: 02/17/2012 EC version: MBECE-0022 ME Version: 8.0.2.1410

AI TWEAKER- DIGI\VRM

AI Overclock Tuner………………………………………………………………..[Manual]
BCLK/PCIE Freq.……………………………………………………………………..[100.0] Always 100,Leave Alone
XMP Memory profile……………………………………………………………...[Disabled]
Turbo ratio By All Cores ………………………………………………………….[Set By “Per Core”, Cannot adjust in OS]
Enter Multiplier Number……….……………………………………………….[47 entered each core]
Internal PLL Overvoltage…………………………………………………………[Disabled]use on 48x and over usually. Or if unsure of computer boot!
Memory Frequency…………………………………………………………………[DDR3-1866]
EPU Power Savings………………………………………………………………….[Disabled]
OC Tuner………………………………………………………………………………….[not used]

DRAM TIMING CONTROL

Primary Timings…………………………………………………………………………[9-10-9-28-2]enter your specific numbers here for primary timings.
All Secondary Timings…………………………………………………………………[Auto]
All Tertiary Timings………………………………………………………………………[Auto]
CPU Power Management……………………………………………………………[Auto]

DIGI + VRM

Load Line Calibration………………………………………………………………….[High]
VRM Frequency…………………………………………………………………………..[Manual]
VRM Fixed Frequency Mode……………………………………………………….[350]
Phase Control……………………………………………………………………………..[Standard]
Duty Control……………………………………………………………………………….[T Probe]
CPU Current Capability………………………………………………………………..[100%]
CPU Voltage…………………………………………………………………………………[Offset]
CPU Offset Mode Sign………………………………………………………………….[+]
CPU Voltage Offset……………………………………………………………………..[0.045v]
Dram Voltage……………………………………………………………………………….[1.50000v]
VCCSA Voltage……Not present on this MB……………………………………[0.92500v] system agent voltage
Leave alone or alternate [Auto] set this to same
VCC10 Voltage…………………………………………………………………………….[1.05000v] Integrated memory Controller, alternate 1.05000v default. [Auto] also sets this okay. max 1.2000v
CPU PLL Voltage…………………………………………………………………………[1.562500v]default is 1.80000v or [Auto]too high a setting! Start at 1.70000v max
PCH Voltage………………………………………………………………………………..[1.050000v]Platform Controller Hub or Auto Leave
Dram Data Reference Voltage/Channel A&B………………………………..[0.50000]
Dram Control Reference Voltage/Channel A&B…………………………….[0.50000]
CPU Spread Spectrum……………………………………………………………………[Auto]Disabled currently

CPU CONFIGURATION

CPU Ratio…………………………………………………………………………………………[Auto]
Initial Adaptive Thermal monitor………………………………………………………[Enabled]
Active processor cores………………………………………………………………………[All]
Limit CPUID Maximum………………………………………………………………………[Disabled]
Execute Disable Bit……………………………………………………………………………[Disabled]
Intel Virtualization technology…………………………………………………………[Disabled]
CPUC1E………………………………………………………………………………………………[Auto]
CPU C3 report……………………………………………………………………………………[Auto]
CPU C6 report……………………………………………………………………………………[Auto]

CPU POWER MANAGEMENT

CPU Ratio……………………………………………………………………………………………[Auto]
Enhanced Intel Speed step Technology………………………………………………[Enabled]
Turbo Mode…………………………………………………………………………………………[Enabled]
Turbo Mode Parameters………………………………………………………………………[Auto]
Long Duration Power Limit……………………………………………………………………[Auto]
Long Duration Maintained……………………………………………………………………[Auto]
Short Duration Power Limit……………………………………………………………………[Auto]
Additional Turbo Voltage………………………………………………………………………[Auto]

Primary Plane Current ……………………………………………………………………………[Auto]

SYSTEM AGENT CONFIGURATION

System Agent Bridge Name………………………………………………………………….Sandybridge
Memory Remap Feature…………………………………………………………………………[Enabled]

Graphics Configuration

Primary Display…………………………………………………………………………………………[PCIE]
iGPU Memory……………………………………………………………………………………………[64m]
Render standby…………………………………………………………………………………………[Enabled]
Set the following item to enabled to enable “Lucid Virtu”
Initiate GPU……………………………………………………………………………………………….[Disabled]

PCH CONFIGURATION

High Precision Timer…………………………………………………………………………………..[Enabled]

SATA CONFIGURATION

SATA Mode ……………………………………………………………………………………………….[AHCI Mode]
SATA 6G-1 & 6G-2 “Grey Ports”…………………………………………………………………[Disabled]
SATA 3G-3, 3G-4,3G- 5 & 3G-6 “Blue Ports-Hot Plugs”………………………………[Enabled]
S.M.A.R.T. Status Check…………………………………………………………………………….[Enabled]

USB CONFIGURATION

Legacy USB Support………………………………………………………………………………….[Enabled]
Legacy USB3.0 Support……………………………………………………………………………..[Enabled]
EHCI Hand-off……………………………………………………………………………………………[Disabled]

ONBOARD DEVICES CONFIGURATION

HD Audio Controller……………………………………………………………………………………[Enabled]
Front Panel…………………………………………………………………………………………………[HD]
SPDIF Out Type……………………………………………………………………………………………[HDMI]
Bluetooth ……………………………………………………………………………………………………[Disabled]
VIA 1394 Firewire…………………………………………………………………………………………[Disabled]
PCI Express slotX16_2 slot (black) bandwidth………………………………………………[Auto]
Marvell Storage Controller…………………………………………………………………………[Disabled]
Realtek Lan Controller…………………………………………………………………………………[Enabled]
Realtek PXE Oprom………………………………………………………………………………………[Disabled]
Asmedia USB 3.0 Controller…………………………………………………………………………[Enabled]
Asmedia USB 3.0 Battery Charging Support…………………………………………………[Disabled]
Serial Port Configuration………………………………………………………………………………[Disabled]

APM

Restore All Power Loss…………………………………………………………………………………[Power Off]
Power on by PCI……………………………………………………………………………………………[Disabled]
Power on by PCIE……………………………………………………………………………………………[Disabled]
Power on by RTC……………………………………………………………………………………………[Disabled]

Monitor-
CPU TEMP/MB TEMP

Chassis Fan Speed 1…………………………………………………………………………………………[Disabled]
Power Fan Speed…………………………………………………………………………………………………[Disabled]
CPU Q fan Control ……………………………………………………………………………………………….[Enabled]
CPU Fan Speed Low Limit…………………………………………………………………………………….[400rpm]
CPU Fan Profile…………………………………………………………………………………………………….[Manual]
CPU Upper Temperature………………………………………………………………………………………[60c]
CPU Fan Maximum Duty Cycle………………………………………………………………………………[100%]
CPU Lower Temperature……………………………………………………………………………………….[20c]
CPU Fan Minimum Duty…………………………………………………………………………………………[20%]
Chassis Q Fan…………………………………………………………………………………………………………[Disabled]
Anti-Surge Support…………………………………………………………………………………………………[Enabled]

BOOT MENU

Boot Num Lock State on …………………………………………………………………………………………[Enabled]
Full Screen Logo ……………………………………………………………………………………………………..[Enabled]
Wait For F1 if Error…………………………………………………………………………………………………..[Enabled]
Option Rom Messages……………………………………………………………………………………………..[Force BIOS]
Set Up Mode (first Bios screen upon entering)…………………………………………………………………………………………………………… ……..[Advanced Mode]
Boot Option Priorities……………………………………………………………. [Hit F8 key to call up Boot menu selection “on the fly” at Asus Logo Screen.]
Boot Option 1……………………………………………………………………………………………………………[wd640]OS hard drive
Boot option 2…………………………………………………………………………………………………………….[disabled]
All other boot options disabled
Boot Override…….. [clicking on any one device initiates booting immediately from that!!]


NOTES:
2 ram stick configurations go in blue slots only
Leave EIST and turbo Boost enabled




With Samsung 30nm ram here below: