Hello guys! Cheers!
I am Simone, and I am writing from Italy! I think you are my last chance to solve my issues (sorry for my english but i am learning it since 6 month :D ). I searched on web people with my same problem and i find only here, some similar issue.
I do not know if you can see my system specifications in my profile, but essentially I bought a ASRock extreme 6 and TermalTake MEKA keyboard (mechanical).
I contacted the ASRock support service, but they answer me with a prefixed reply (i.e: update BIOS, chance Keyboard, clear CMOS) without solve problems. Following the two problem (first most important):
1) I CAN NOT ENTER THE UEFI PRESSING F2 or CANC
Clear CMOS do not avoid the access problems (as suggested from ASRock tech support) . However, by this way I can enter the UEFI at least one time, just after the CMOS reset (when the system waiting my input). Obviously it can not be the way to avoid the problem, because every times the OC setup will be cleared. But, thanks to the browsing in the UEFI, I found somethin.
First, changing the bios option that sets the waiting time for BIOS input choice, up to 5 seconds (on BIOS card of UEFI, default is 1 second), i am able to enter the UEFI all times. But obviously i don't like wait 5 second for start up, when i buy a SSD for 200 $ that require just 8 seconds to make my system ready to work. It an increase of 62.5% on start up time!
I tried with another keyboard (USB but not-mechanical, from ASRock tech support) and it works properly. Searching on web i found (here) a lot of problem of ASRock motherboard with mechanical keyboard, with the same my issue. The motherboard do not accept input by mechanical keyboard during POST phase.
I do not understand if this is a official ASRock forum, or how a beta version of BIOS can be distributed by a forum (Emily?!), but someone can solve his problem by this way.
Maybe you can help me please?!
2) XfastUSB (FAST MODE) DO NOT WORKS PROPERLY WITH USB 3.0 DEVICES ON: 19 PIN HEADER OF MOTHERBOARD AND TWO LOWER PORT OF I/O PANNEL (OTHERWISE WORKS in THE TWO UPPER PORT OF I/O PANNEL)
XFastUSB works very well on the USB 2.0 port, with both 2.0 and 3.0 pen drives. It improves sequential write and read. But, fast mode on USB 3.0 port, with both 2.0 and 3.0 pen drives, dosen't work properly (in my system). Actually, the problem appears when i connect the 3.0 pen drive on the 20(19) pin header on the mobo or on the 2 lower 3.0 port of rear I/O panel.
Contrariwise, if I connect the 3.0 drive on the upper 3.0 port of rear I/O panel, the XfastUSB does not made any issue (actually there aren't any benefits with respect to 3.0 normal mode, but i think, that happens because velocity of pen drive is satured).
The issue that happens is a very low read/write velocity and the green bar, that show the progress of action, moves discontinuously. Seems that for few moment, the copy falls asleep, then resumes, then falls asleep again and again.
Any ideas?!
3) Finally, I would like disable the Intel Managment Engine hardware from UEFI (i do not like it and not even the unknow hardware with a yellow ! ), but i cant find it on UEFI. Someone know the position of this options?!
Thank you guys, for your help and your time!
I am Simone, and I am writing from Italy! I think you are my last chance to solve my issues (sorry for my english but i am learning it since 6 month :D ). I searched on web people with my same problem and i find only here, some similar issue.
I do not know if you can see my system specifications in my profile, but essentially I bought a ASRock extreme 6 and TermalTake MEKA keyboard (mechanical).
I contacted the ASRock support service, but they answer me with a prefixed reply (i.e: update BIOS, chance Keyboard, clear CMOS) without solve problems. Following the two problem (first most important):
1) I CAN NOT ENTER THE UEFI PRESSING F2 or CANC
Clear CMOS do not avoid the access problems (as suggested from ASRock tech support) . However, by this way I can enter the UEFI at least one time, just after the CMOS reset (when the system waiting my input). Obviously it can not be the way to avoid the problem, because every times the OC setup will be cleared. But, thanks to the browsing in the UEFI, I found somethin.
First, changing the bios option that sets the waiting time for BIOS input choice, up to 5 seconds (on BIOS card of UEFI, default is 1 second), i am able to enter the UEFI all times. But obviously i don't like wait 5 second for start up, when i buy a SSD for 200 $ that require just 8 seconds to make my system ready to work. It an increase of 62.5% on start up time!
I tried with another keyboard (USB but not-mechanical, from ASRock tech support) and it works properly. Searching on web i found (here) a lot of problem of ASRock motherboard with mechanical keyboard, with the same my issue. The motherboard do not accept input by mechanical keyboard during POST phase.
I do not understand if this is a official ASRock forum, or how a beta version of BIOS can be distributed by a forum (Emily?!), but someone can solve his problem by this way.
Maybe you can help me please?!
2) XfastUSB (FAST MODE) DO NOT WORKS PROPERLY WITH USB 3.0 DEVICES ON: 19 PIN HEADER OF MOTHERBOARD AND TWO LOWER PORT OF I/O PANNEL (OTHERWISE WORKS in THE TWO UPPER PORT OF I/O PANNEL)
XFastUSB works very well on the USB 2.0 port, with both 2.0 and 3.0 pen drives. It improves sequential write and read. But, fast mode on USB 3.0 port, with both 2.0 and 3.0 pen drives, dosen't work properly (in my system). Actually, the problem appears when i connect the 3.0 pen drive on the 20(19) pin header on the mobo or on the 2 lower 3.0 port of rear I/O panel.
Contrariwise, if I connect the 3.0 drive on the upper 3.0 port of rear I/O panel, the XfastUSB does not made any issue (actually there aren't any benefits with respect to 3.0 normal mode, but i think, that happens because velocity of pen drive is satured).
The issue that happens is a very low read/write velocity and the green bar, that show the progress of action, moves discontinuously. Seems that for few moment, the copy falls asleep, then resumes, then falls asleep again and again.
Any ideas?!
3) Finally, I would like disable the Intel Managment Engine hardware from UEFI (i do not like it and not even the unknow hardware with a yellow ! ), but i cant find it on UEFI. Someone know the position of this options?!
Thank you guys, for your help and your time!
Comment