Re: ? on swapping RAM on a Gigabyte EP45-UD3R rev 1.1
I don't NEED it but it's what's being offered as a replacement at no cost to me. I will say that I have seen Win 7 perform a little better when jumping from 4 to 8G when 4G seemed to be ample for my needs. I think Windows just like...
No announcement yet.
User Profile
Collapse
Profile Sidebar
Collapse
SBMongoos
Member
Last Activity: 09-03-2011, 09:23 AM
Joined: 02-03-2009
Location:
-
? on swapping RAM on a Gigabyte EP45-UD3R rev 1.1
I have 2x2 (4G) kit of OCZ Reaper series RAM. It's PC2-9200/1150Mhz. I have the option to swap out to 2 - 2x2 (total 8G) OCZ Vista Upgrade DDR2 PC2-6400/800Mhz. Both have the timings of CL 5-6-6-18 (CAS-TRCD-TRP-TRAS). The Reaper series has voltage of 2.1 and the Vista series is 1.8v. I have the...
-
Re: Unable to access any PC via Network on Win7 Pro PC
Anyone?Last edited by SBMongoos; 03-17-2011, 09:02 PM.
Leave a comment:
-
Unable to access any PC via Network on Win7 Pro PC
Odd, at my laptop (Win7 HP 64bit) I can access my desktop (Win7 Pro 64bit) and laptop via "network" in My Computer from the laptop. But on my desktop I cannot access the laptop or even the desktop (same machine). I get the following message:
Click here
I've uninstalled...
-
Flash header not aligning properly
I've created a flash movie for my header but in IE and FF it does not line up where it should at the bottom. There is a small gap between the bottom of the swf and the blue line just above the menu. It looks good in Opera, Chrome and Safari. Cannot figure what I need to do.
Almost there!...Last edited by SBMongoos; 02-11-2010, 11:40 PM.
-
Re: Stable E8400 OC - stock voltages
Okay...I gave up again as it seems to take forever to go through the steps to find the right settings. I went back to the 3.83 settings.
But I have to say. When I swap out my XP HDD to my 7 HDD and run 7 I expect the data transfer speed...
Leave a comment:
-
Re: Stable E8400 OC - stock voltages
You set your swapfile to a fixed sized based on the amount of RAM do you do let the sytem manage it? I've been using 1.5 X amount of RAM and setting it to a fixed size. Curious since you're using a partition for your swapfile.
...Last edited by SBMongoos; 12-04-2009, 11:48 AM.
Leave a comment:
-
Re: Stable E8400 OC - stock voltages
What's the reg tweak?...
Leave a comment:
-
Re: Stable E8400 OC - stock voltages
Okay....so it may make sense to do for Win 7 if I want to hotswap our get an SSD drive down the road. But, this would have to be setup during install of Win 7 correct? Not changed in the BIOS after the fact?...
Leave a comment:
-
Re: Stable E8400 OC - stock voltages
I was under the impressin that it was better to use AHCI for Vista or 7. Not sure what the SATA PORT 0-3 NATIVE MODE does.
- SATA RAID/AHCI MODE
- Disabled
- RAID
- AHCI Mode
- SATA PORT
Leave a comment:
- SATA RAID/AHCI MODE
No activity results to display
Show More
Leave a comment: