-
Last edited by stasio; 09-15-2021, 12:10 PM. -
Comment
-
Comment
-
Has 3 things.....Originally posted by shiecldk View Post
- Acebmxer is no more active here
- I also stop modified BIOS, long time ago
- No BIOS P67A-UD3R-B3 U1C linkComment
-
Thank you! The BIOS link is in here: U1COriginally posted by stasio View Post
Do you know where is the guide for updating
- CPU MicroCode Pack
- Intel PCI Accelerated SVGA BIOS
- Intel Legacy RAID ROM
- Modified splash logo 2
I remember there were guides for these things years ago but they seem to be disappear now. I know how to do all of the rest mods shown in the first page except these ones above.
GA-P67A-UD3R BIOS U1b mod2
Modified with :
Intel Legacy RAID ROM 11.1.0.1413 to 12.7.0.1936
Intel UEFI SataDriver 11.6.0.1702 to 12.7.0.1936
Realtek PCIe GBE Controller 2.50 to 2.58
Intel PCI Accelerated SVGA BIOS 2158
Sandy GOPdriver 2.0.1023 (to 2.0.1024 in mod2gop)
Ivy GOPdriver 3.0.1023
CPU MicroCode Pack (with Sandy 6A728 and Ivy 6A919)
ME Firmware 8.0.0.1351 to 8.1.51.1471
Modified splash logoComment
-
Thanks again stasioOriginally posted by stasio View Post
One more question... Gigabyte seems messed up the product name of the U1C BIOS of P67A-UD3R-B3. I found the name in the BIOS is for P67A-UD3R (without B3) and I cannot flash the BIOS when Q-FLASH is checking for the id. Hence, in order to bypass the Q-FLASH check, I change the HEX string in the BIOS from
38 41 32 31 41 47 30 51
to
38 41 32 31 41 47 30 57
This successfully allows me to flash the U1C BIOS.
However, I wonder how can I change the name in the BIOS from P67A-UD3R to P67A-UD3R-B3? Do I need to use AMIBCP to make the name change? Thanks again!Comment
-
Update: I edited the name with the DMI tab in AMIBCP and saved the bios. It doesn't seem to make any changes after I flashed the mod bios. The bios menu still shows P67A-UD3R (without B3).Comment
-
After trying to enable virtualization on my 2012 GA Z77-D3H v 1.0 motherboard, the board could not boot Windows properly anymore, and got ACPI.sys error, so after the restart after the bios logo appeared, I Could not enter the bios, by using F12, or Del or End key. After bios reset the backup bios determined that the amin bios is corrupted and triggered the main bios recovery but is constantly stuck on 0%. Boot is also screwed as the board bios has been reset, so I cannot enter the boot menu and it does not boot into the second windows to try to flash the bios, as I cannot get Qflash to reflash normally.
I wonder if there is keyboard combination to trigger/force the bios upgrade from the USB stick plugged in the Intel USB ports that get initialized during the boot.
Please help, as I am stuck and on the end of my tether with corrupted Z77 bios.
Please advise, how can I proceed to recover/reflash the bios in this specific scenario?
How can I boot from the USB bios recovery stick and how to create the one for my Gigabyte board?
Disconnecting everything (sata cables, drives, etc, did not make any changes, as well as removing all the ram sticks but one, although the board correctly detects if there is no ram sticks in the slot? Attached is the screenshot of the stuck bios recovery screen!Comment
-
When both BIOS's are corrupted, you need "CH341A Programmer" (complet with cables....less then 10 USD).Originally posted by mztech View Post
Go to https://www.win-raid.com and read about.
It's happen to me with Z79X (MX25L12873F BIOS chip), now all OK.
Last edited by stasio; 11-01-2021, 02:23 AM.Comment
-
Help me modify the BIOS for GA-965QM-DS2 (rev. 2.0) Intel Core 2 Quad Q9505 I would be very grateful! https://download.gigabyte.com/FileLi...986c6e9da2f5e9Comment
-
Comment
-
Hi!Originally posted by chipyto View Post
i have a bios with TPM2.0 for Z97X-Gaming3 but i dont know how is possible that. This bios work and permit install W11 without any tricks.
Comment
Tweet
Comment