Hi,
I took my time and read various threads with similar issues still a few questions arise.
The current settings are:
CPU = E5200 R0 (1.265 VID) , FSB wall appears to be at 350 MHz
Motherboard = EP45-UD3LR, rev1.0
BIOS Version = F5
Ram = GSKILL PI Black, F2-6400CL4D-4GBPI-B, http://www.gskill.com/products.php?index=167
GPU Nvidia 9500GT, 1Gb mem (stock clocks)
PSU Seasonic 620W
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 12
Fine CPU Clock Ratio.....................: 0
CPU Frequency ...........................: 4000
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 333 Mhz
PCI Express Frequency (Mhz) .........: 100
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 900
PCI Express Clock Drive.................: 800
CPU Clock Skew (ps)....................: 0
MCH Clock Skew (ps)...................: 0
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: 333
System Memory Multiplier ..............: 2.40B
Memory Frequency (Mhz) ..............: 800
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................ 4
tRCD ......................................... 4
tRP'........................................... 4
tRAS.......................................... 12
Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go
Advanced Timing Control
tRRD........................................... 3
tWTR.......................................... 3
tWR............................................ 6
tRFC........................................... 52
tRTP........................................... 3
Command Rate (CMD) ....................: 0
Channel A
Static tRead Value.........................: 6
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Channel B
Static tRead Value.........................:6
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Motherboard Voltage Control
CPUMCH/ICHDRAMAdvanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Integrated Peripherals
Legacy USB Storage Detect ..............[Enabled]
1. Why my cpu GTL (Reference) isn't set correctly by auto, as far as I know it should be about 0.63-0.64 of VTT ?
2. What is the suggested VTT for my scenario, should I approach Vcore with it?
3. Why the MCH (NB) voltage need to be increased, the chipset should handle the 333 MHz FSB easily ?
4. Another minor issue is that I can't find E5200 R0 official support on Gigabyte website only M0 stepping, should I try the F10 BIOS maybe ?
I can run stable and cool on 333x11.5=3.83GHz. still I want to push a bit more as my cooling allows this.
Help will be appreciated.
</pre>
I took my time and read various threads with similar issues still a few questions arise.
The current settings are:
CPU = E5200 R0 (1.265 VID) , FSB wall appears to be at 350 MHz
Motherboard = EP45-UD3LR, rev1.0
BIOS Version = F5
Ram = GSKILL PI Black, F2-6400CL4D-4GBPI-B, http://www.gskill.com/products.php?index=167
GPU Nvidia 9500GT, 1Gb mem (stock clocks)
PSU Seasonic 620W
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 12
Fine CPU Clock Ratio.....................: 0
CPU Frequency ...........................: 4000
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 333 Mhz
PCI Express Frequency (Mhz) .........: 100
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 900
PCI Express Clock Drive.................: 800
CPU Clock Skew (ps)....................: 0
MCH Clock Skew (ps)...................: 0
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: 333
System Memory Multiplier ..............: 2.40B
Memory Frequency (Mhz) ..............: 800
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................ 4
tRCD ......................................... 4
tRP'........................................... 4
tRAS.......................................... 12
Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go
Advanced Timing Control
tRRD........................................... 3
tWTR.......................................... 3
tWR............................................ 6
tRFC........................................... 52
tRTP........................................... 3
Command Rate (CMD) ....................: 0
Channel A
Static tRead Value.........................: 6
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Channel B
Static tRead Value.........................:6
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Motherboard Voltage Control
CPUMCH/ICHDRAMAdvanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Integrated Peripherals
Legacy USB Storage Detect ..............[Enabled]
1. Why my cpu GTL (Reference) isn't set correctly by auto, as far as I know it should be about 0.63-0.64 of VTT ?
2. What is the suggested VTT for my scenario, should I approach Vcore with it?
3. Why the MCH (NB) voltage need to be increased, the chipset should handle the 333 MHz FSB easily ?
4. Another minor issue is that I can't find E5200 R0 official support on Gigabyte website only M0 stepping, should I try the F10 BIOS maybe ?
I can run stable and cool on 333x11.5=3.83GHz. still I want to push a bit more as my cooling allows this.
Help will be appreciated.
</pre>
Comment