HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everything

[ExoD]

[thanhhaimai]

Re: HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everyth

Just curious, why do you have to set the PCI Express Clock Drive to 700mV? You may want to set it back to 900mV

Also, why do you have to set those settings? I suggest to leave it Auto for now.

Trd2rd(Different Rank)....................: 6
Twr2wr(Different Rank)...................: 6
Twr2rd(Different Rank)...................: 5
Trd2wr(Same/Diff Rank)..................: 8

Also set Vcore, VTT, PLL, to the value on the left, don't set it on Auto. And is your DRAM Voltage manufacture recommended? If you're not overclocking, then set it to the manufactured voltage.

Hope this help.

[ExoD]

Re: HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everyth

I had them set and it still crashed so i went back to auto.....

[thanhhaimai]

Re: HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everyth

How about the timings, PCI-E clock drive (900mV) and CPU clock drive (800mV)? You should set them back to default and auto.

[ExoD]

Re: HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everyth

Set them to 900MV and 800Mv. Ran prime 95 and it crashed again.

[thanhhaimai]

Re: HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everyth

Please post your updated BIOS settings again. How long did prime95 run? How long did you test your memory sticks? What was the crash message if it was a BSOD?

[ExoD]

[thanhhaimai]

Re: HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everyth

If it crashes on 12k FFT test then mostly it's a CPU problem. But your other errors seem like a memory problem or a faulty board but I'm not quite sure.

Last try:

(G)MCH Frequency Latch...............: [266 MHz] <--- set this Auto
System Memory Multiplier ..............: 3.00A <--- set this 2.00B or 2.00D (try both to see if it works)
tRRD...........................................4 <--- set this Auto
tWTR..........................................4 <--- set this Auto
tWR............................................8 <--- set this Auto
tRFC...........................................68 <--- set this Auto
tRTP...........................................4 <--- set this Auto
CPU Termination�..... 1.200V*.......: (1.2) <--- try to increase it to 1.3V to see if it helps.
No-Execute Memory Protect............: [Enabled] <--- Disable for now

If this still doesn't work then I suggest you to wait for Lsdmeasap or someone more experienced than me to help you. I don't see why your settings won't work. Your CPU is not overclocked at all.

[ExoD]

Re: HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everyth

I will check those settings out. If you think of anything else let me know. I will let you know the results.

[profJim]

Re: HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everyth

Don't manually change the Clock Drive settings.
700/700 are the default values when you load Fail-Safe settings. These should be named Failure-Prone settings!
You want to load Optimized Bios settings before you make any bios changes. The optimized defaults change some hidden bios settings that are required for stable operation.

You will make it much easier for us to help you if you provide the detailed information in steps 1 - 4 in this post.
Please add your detailed hardware information, bios version, mobo version and a link to your memory in your forum signature and post the screen-shot in step 4.

Set tRFC = 72 - 74 with 8GB of memory.
MCH Core = 1.32 - 1.36 might be needed.
CPU Termination = 1.22 - 1.26 should help.

If these settings don't help, try testing with only 2x2GB of memory with MCH Core = 1.22 - 1.24 volts.

[Lsdmeasap]

Re: HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everyth

Those were seto to 700 because you were starting from fail safe BIOS settings, please start over by loading optimized defaults then save/apply/reboot BACK to the BIOS. Then make any needed changes, including your SATA/RAID Settings before going to windows.

Once you do this, then try your overclock again and give us your new settings. This is a must because there is setting you cannot access, and starting from fail safe will set these wrong.

Are your MCH/CPU ect, REF's on Auto where you entered values such as "MCH Reference….…….0.800V...........; (0.760)" or are you manually setting something? Just checking.

Post back your new attempts settings once you start with optimized, and also please include a link to your memory and a screenshot of Memset and CPU-z open

[ExoD]

Re: HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everyth

I Loaded optimized settings. And below is what i currently am running on. Im manually setting them.

Corsair Dominator TWIN2x2048-8500C5D
http://www.corsair.com/_datasheets/t...48-8500c5d.pdf



MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 10x
CPU Frequency ...........................: 2.66 (266x10)


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 266
PCI Express Frequency (Mhz) .........: 100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800Mv
PCI Express Clock Drive.................: 900mV
CPU Clock Skew (ps)....................: 0
MCH Clock Skew (ps)...................: 0


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: [Disabled]
(G)MCH Frequency Latch...............: [266 MHz]
System Memory Multiplier ..............: 3.00A
Memory Frequency (Mhz) ..............: 800
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................15

Advanced Timing Control
tRRD...........................................4
tWTR..........................................4
tWR............................................8
tRFC...........................................72
tRTP...........................................4
Command Rate (CMD) ....................:0 [AUTO]

Channel A
Static tRead Value.........................:Auto
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................: Auto
Twr2wr(Different Rank)...................: Auto
Twr2rd(Different Rank)...................: Auto
Trd2wr(Same/Diff Rank)..................: Auto
Dimm1 Clock Skew Control...............:Auto
Dimm2 Clock Skew Control...............:Auto
DDR Write Training..........................:Auto

Channel B
Static tRead Value.........................:Auto
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................: Auto
Twr2wr(Different Rank)...................: Auto
Twr2rd(Different Rank)...................: Auto
Trd2wr(Same/Diff Rank)..................: Auto
Dimm1 Clock Skew Control...............:Auto
Dimm2 Clock Skew Control...............:Auto
DDR Write Training..........................:Auto


<?xml:namespace prefix = o ns = "urn:schemas-microsoft-com:office:office" /><o:p></o:p>Motherboard Voltage Control

CPU






MCH/ICH






DRAM


Channel A Reference 0.900V............: 0.900
Channel B Reference 0.900V............: 0.900

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Disabled]
CPU Enhanced Halt (C1E)................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]

Integrated Peripherals
USB Keyboard..................................[Enabled]
USB Mouse......................................[Enabled]
USB Storage....................................[Enabled]

[profJim]

Re: HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everyth

Are you running any stress/stability tests? IBT? Prime95? OCCT?

Please confirm if the following settings are correct and manually set or if they are set to AUTO:
MCH Reference ----- 0.800V -----: 0.760
MCH/DRAM Ref ------ 0.900V -----: 0.900

DRAM Termination -- 0.900V------: 0.900
Channel A Reference 0.900V -----: 0.900
Channel B Reference 0.900V----- : 0.900

Do you want to overclock your system once you're system is stable at stock settings? If yes, what is your o/c goal?

[Chike]

Re: HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everyth

CPU Termination in the template also does not match the screen shot.

[Lsdmeasap]

Re: HELP! UD3P+QX6700+Corsair 2x2048-8500C5D keeps crashing please help tryed everyth

When you manually set what I asked, are you doing it properly as per the guide in my signature? If not please set them to Auto for now

tRD is likely the problem, 5 is to low and MCH may be too high

Please try these settings for 800Mhz

Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 10x
CPU Frequency ...........................: 2.66 (266x10)


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 266
PCI Express Frequency (Mhz) .........: 100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800Mv
PCI Express Clock Drive.................: 900mV
CPU Clock Skew (ps)....................: 0
MCH Clock Skew (ps)...................: 0


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: [Disabled]
(G)MCH Frequency Latch...............: [266 MHz] << Auto
System Memory Multiplier ..............: 3.00A
Memory Frequency (Mhz) ..............: 800
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................15/18

Advanced Timing Control
tRRD...........................................3-4
tWTR..........................................3-6
tWR............................................4-8
tRFC...........................................68-74
tRTP...........................................4-5
Command Rate (CMD) ....................:0 [AUTO] << Set 2T

Channel A
Static tRead Value.........................:Auto << set 8-9 for now
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................: Auto
Twr2wr(Different Rank)...................: Auto
Twr2rd(Different Rank)...................: Auto
Trd2wr(Same/Diff Rank)..................: Auto
Dimm1 Clock Skew Control...............:Auto
Dimm2 Clock Skew Control...............:Auto
DDR Write Training..........................:Auto

Channel B
Static tRead Value.........................:Auto << set 8-9 for now
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................: Auto
Twr2wr(Different Rank)...................: Auto
Twr2rd(Different Rank)...................: Auto
Trd2wr(Same/Diff Rank)..................: Auto
Dimm1 Clock Skew Control...............:Auto
Dimm2 Clock Skew Control...............:Auto
DDR Write Training..........................:Auto


Motherboard Voltage Control

CPU
CPU Vcore….……….........................: 1.33750

CPU Termination…..... 1.200V*.......: 1.26 << may need 1.3-1.32
CPU PLL…………………....1.500V*.......: 1.5
CPU Reference.…………....0.755V*.......: 0.760 << Auto

MCH/ICH
MCH Core…………….....1.100V...........: 1.32 << 1.28-1.3 may be ok
MCH Reference….…….0.800V...........: 0.760 << Auto
MCH/DRAM Ref.…......0.900V...........: 0.900 << Auto
ICH I/O……………….....1.500V............: 1.500
ICH Core…………...……1.100V............: 1.14-1.2

DRAM
DRAM Voltage ……....1.800V............: 2.100 << may need a bit more 2.15-2.2
DRAM Termination .…0.900V............: 0.900 << Auto
Channel A Reference 0.900V............: 0.900 << Auto
Channel B Reference 0.900V............: 0.900 << Auto