Tweet
GA-P55A-UD3P & i5 750 cant startup/install windows
I searched through the forums for awhile and couldn't find someone with quite the same problem as me. I built the new system a few days ago and no matter what I try it cant start up any operating system or install a new one. I can get to the bios no problem, and it loads and recognizes the drives, however at startup as soon as the loading screen comes it restarts. When I try and install windows 7 (32 or 64) it loads the files but never shows the install interface.
Mobo: GA-P55A-UD3P
Memory: 996657 - 4GB (2x2GB) DDR3 PC3-12800 7-7-7-20 Blackline (Dual Kit)
PSU: CORSAIR CMPSU-650HX 650W
CPU: i5 750
I set the BIOS to optimized defaults, I tryed a lot of suggestions from other posts but no luck. for now I would just like to get my system running and worry about overclocking later.
Advanced Frequency Settings:
CPU Clock Ratio 20x
Advanced Core Features [Press Enter]:
Intel(R) Turbo Boost Tech................[Disabled]
CPU Cores Enabled........................[All]
CPU Multi-Threading......................N/A
CPU Enhanced Halt (C1E)..................[Auto]
C3/C6/C7 State Support...................[Auto]
CPU Thermal Monitor......................[Auto]
CPU EIST Function........................[Auto]
Bi-Directional PROCHOT...................[Auto]
QPI Clock Ratio..........................[Auto]
QPI Link Speed........................[4.86GHz]
Uncore Clock Ratio....................[16x]
Uncore Frequency.........................2133MHz
>>>>> Standard Clock Control <<<<<
Base Clock (BCLK) Control................[Disabled]
BCLK Frequency ..........................[133]
Extreme Memory Profile (X.M.P.)..........[Disabled]
System Memory Multiplier (SPD)...........[Disabled]
Memory Frequency (MHz)................1333
PCI Express Frequency (MHz)..............[100]
C.I.A.2..................................[Disabled]
>>>>> Advanced Clock Control <<<<<
CPU Clock Drive..........................[ 800mV]
PCI Express Clock Drive..................[ 900mV]
CPU Clock Skew...........................[ 0ps]
Advanced Memory Settings:
Extreme Memory Profile (X.M.P.)..........[Disabled]
System Memory Multiplier (SPD)...........[Auto]
Memory Frequency (MHz)................1333
Performance Enhance (SPD)............. [Turbo]
DRAM Timing Selectable (SPD)............ [Auto]
Profile DDR Voltage ..................
Profile QPI Voltage ..................
Channel Interleaving.....................[Auto]
Rank Interleaving........................[Auto]
>>>>> Channel A & B
Channel A Timing Settings [Press Enter]:
Cas Latency Time........................[9]
tRCD....................................[9]
tRP.....................................[9]
tRAS...................................[24]
>>>>> Advanced Timing Control
tRC....................................[Auto]
tRRD...................................[Auto]
tWTR...................................[Auto]
tWR....................................[Auto]
tWTP...................................[Auto]
tWL....................................[Auto]
tRFC...................................[Auto]
tRTP...................................[Auto]
tFAW...................................[Auto]
Command Rate (CMD).................. 1 [Auto]
>>>>> Misc Timing Control
B2B Cas Delay..........................[Auto]
Round Trip Latency...................46[Auto]
Channel A Turnaround Settings [Press Enter]:
Different DIMMs........................[Auto]
Different DIMMs........................[Auto]
On The Same Rank.......................[Auto]
>>>>> Channel A Writes Followed By Writes
Different DIMMs........................[Auto]
Different DIMMs........................[Auto]
On The Same Rank.......................[Auto]
Advanced Voltage Settings:
******Mother Board Voltage Control ******
Voltage Types............Normal......Current
--------------------------------------------
>>> CPU
Load Line Calibration...................[Auto]
CPU Vcore..................1.23750v..[Auto]
QPI/VTT Voltage..........1.100v.....[Auto]
>>> MCH/ICH
PCH Core....................1.050v.....[Auto]
CPU PLL......................1.800v.....[Auto]
>>> DRAM
DRAM Voltage..............1.500v.....[Auto]
DRAM Termination.........0.750v.....[Auto]
Ch-A Data VRef............0.750v.....[Auto]
Ch-A Data VRef............0.750v.....[Auto]
Ch-B Data VRef............0.750v.....[Auto]
Ch-B Data VRef............0.750v.....[Auto]
Mobo: GA-P55A-UD3P
Memory: 996657 - 4GB (2x2GB) DDR3 PC3-12800 7-7-7-20 Blackline (Dual Kit)
PSU: CORSAIR CMPSU-650HX 650W
CPU: i5 750
I set the BIOS to optimized defaults, I tryed a lot of suggestions from other posts but no luck. for now I would just like to get my system running and worry about overclocking later.
Advanced Frequency Settings:
CPU Clock Ratio 20x
Advanced Core Features [Press Enter]:
Intel(R) Turbo Boost Tech................[Disabled]
CPU Cores Enabled........................[All]
CPU Multi-Threading......................N/A
CPU Enhanced Halt (C1E)..................[Auto]
C3/C6/C7 State Support...................[Auto]
CPU Thermal Monitor......................[Auto]
CPU EIST Function........................[Auto]
Bi-Directional PROCHOT...................[Auto]
QPI Clock Ratio..........................[Auto]
QPI Link Speed........................[4.86GHz]
Uncore Clock Ratio....................[16x]
Uncore Frequency.........................2133MHz
>>>>> Standard Clock Control <<<<<
Base Clock (BCLK) Control................[Disabled]
BCLK Frequency ..........................[133]
Extreme Memory Profile (X.M.P.)..........[Disabled]
System Memory Multiplier (SPD)...........[Disabled]
Memory Frequency (MHz)................1333
PCI Express Frequency (MHz)..............[100]
C.I.A.2..................................[Disabled]
>>>>> Advanced Clock Control <<<<<
CPU Clock Drive..........................[ 800mV]
PCI Express Clock Drive..................[ 900mV]
CPU Clock Skew...........................[ 0ps]
Advanced Memory Settings:
Extreme Memory Profile (X.M.P.)..........[Disabled]
System Memory Multiplier (SPD)...........[Auto]
Memory Frequency (MHz)................1333
Performance Enhance (SPD)............. [Turbo]
DRAM Timing Selectable (SPD)............ [Auto]
Profile DDR Voltage ..................
Profile QPI Voltage ..................
Channel Interleaving.....................[Auto]
Rank Interleaving........................[Auto]
>>>>> Channel A & B
Channel A Timing Settings [Press Enter]:
Cas Latency Time........................[9]
tRCD....................................[9]
tRP.....................................[9]
tRAS...................................[24]
>>>>> Advanced Timing Control
tRC....................................[Auto]
tRRD...................................[Auto]
tWTR...................................[Auto]
tWR....................................[Auto]
tWTP...................................[Auto]
tWL....................................[Auto]
tRFC...................................[Auto]
tRTP...................................[Auto]
tFAW...................................[Auto]
Command Rate (CMD).................. 1 [Auto]
>>>>> Misc Timing Control
B2B Cas Delay..........................[Auto]
Round Trip Latency...................46[Auto]
Channel A Turnaround Settings [Press Enter]:
Different DIMMs........................[Auto]
Different DIMMs........................[Auto]
On The Same Rank.......................[Auto]
>>>>> Channel A Writes Followed By Writes
Different DIMMs........................[Auto]
Different DIMMs........................[Auto]
On The Same Rank.......................[Auto]
Advanced Voltage Settings:
******Mother Board Voltage Control ******
Voltage Types............Normal......Current
--------------------------------------------
>>> CPU
Load Line Calibration...................[Auto]
CPU Vcore..................1.23750v..[Auto]
QPI/VTT Voltage..........1.100v.....[Auto]
>>> MCH/ICH
PCH Core....................1.050v.....[Auto]
CPU PLL......................1.800v.....[Auto]
>>> DRAM
DRAM Voltage..............1.500v.....[Auto]
DRAM Termination.........0.750v.....[Auto]
Ch-A Data VRef............0.750v.....[Auto]
Ch-A Data VRef............0.750v.....[Auto]
Ch-B Data VRef............0.750v.....[Auto]
Ch-B Data VRef............0.750v.....[Auto]
Comment