No announcement yet.

GIGABYTE GA-EP45-UD3R Memory settings

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • GIGABYTE GA-EP45-UD3R Memory settings

    Well moving on for USB problems..now to tweak a little
    Running E8500 at 3.6ghz
    Using memset 4.0 here is what it shows

    found this pic

    My ram is Mush 2x2gb model 991580
    Last edited by man00; 03-13-2009, 11:21 AM.

  • #2
    Re: GIGABYTE GA-EP45-UD3R Memory settings

    Well, several of those can for sure come down, some more then other. But in general they are all pretty loose

    I can't for sure see that ram speed, is it 462 or 483?

    Comment


    • #3
      Re: GIGABYTE GA-EP45-UD3R Memory settings

      463 fsb:dram 5:6 I have never messed with ram setting other than voltage.

      Comment


      • #4
        Re: GIGABYTE GA-EP45-UD3R Memory settings

        What? I understand you about FSB 463, and ram 2.40B, but I do not see that in your image above? I see ram showing in memset at 4xx something, not 511 or so as it would be if you were using 463FSB x 2.40B


        Can you post a larger image? Or just give me your full exact BIOS settings, then if you want (Let me know) I can advise you back some optimal settings.

        This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

        Code:
        [b][u]MB Intelligent Tweaker(M.I.T.)[/u][/b]
        Robust Graphics Booster ...............: Auto or Fast
        CPU Clock Ratio ..........................: 
        Fine CPU Clock Ratio.....................:.0
        CPU Frequency ...........................: 
        
        
        [b][u]Clock Chip Control [/u][/b]
        [b][u]Standard Clock Control[/u][/b]
        CPU Host Clock Control..................: [Enabled] 
        CPU Host Frequency (Mhz) ............: Mhz
        [B]PCI Express Frequency (Mhz) .........:Set to 100[/B]
        
        C.I.A.2 .................................:[Disabled]
        
        
        [b][u]Advanced Clock Control [Press Enter][/u][/b]
        CPU Clock Drive...........................: <<< 800
        PCI Express Clock Drive.................: <<< 900
        CPU Clock Skew (ps)....................: <<< 
        MCH Clock Skew (ps)...................: <<< 
        
        
        [b][u]DRAM Performance Control[/u][/b][u][/u]
        [B]Performance Enhance...................: [STANDARD][/B]
        Extreme Memory Profile (X.M.P.).....: Disabled
        (G)MCH Frequency Latch...............: [Auto]
        System Memory Multiplier ..............: 
        Memory Frequency (Mhz) ..............: 
        DRAM Timing Selectable ................: [Manual]
        
        [b]Standard Timing Control[/b]
        CAS Latency Time........................
        tRCD .........................................
        tRP'...........................................
        tRAS..........................................
        
        Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go
        
        [b][u]Advanced Timing Control[/u][/b]
        tRRD...........................................
        tWTR..........................................
        tWR............................................
        tRFC...........................................
        tRTP...........................................
        Command Rate (CMD) ....................:2
        
        [u][b]Driving Strength Profiles[/b][/u][b][/b]
        Driving Strength ............................
        
        [b]Channel A[/b]
        Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
         tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
        tRD Phase1 Adjustment...................:Auto
         tRD Phase2 Adjustment .................:Auto
         tRD Phase3 Adjustment..................:Auto
        Trd2rd(Different Rank)....................:Auto 
        Twr2wr(Different Rank)...................:Auto 
        Twr2rd(Different Rank)...................:Auto 
        Trd2wr(Same/Diff Rank)..................:Auto 
        Dimm1 Clock Skew Control...............:Auto  ps
        Dimm2 Clock Skew Control...............:Auto  ps
        
        [b]Channel B[/b]
        Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
         tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
        tRD Phase1 Adjustment...................:Auto
         tRD Phase2 Adjustment .................:Auto
         tRD Phase3 Adjustment..................:Auto
        Trd2rd(Different Rank)....................:Auto 
        Twr2wr(Different Rank)...................:Auto 
        Twr2rd(Different Rank)...................:Auto 
        Trd2wr(Same/Diff Rank)..................:Auto 
        Dimm1 Clock Skew Control...............:Auto  ps
        Dimm2 Clock Skew Control...............:Auto  ps
        
        [b][U]Motherboard Voltage Control[/U][/b][U][/U]
        Voltage Type.………... Manual
        [b]CPU[/b]
        CPU Vcore….……….........................:Auto if not overclocking, if you are overclocking please do find and set your own voltages
        
        CPU Termination…..... 1.200V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.2-1.5 depending on Vcore, try to keep at least .1 under vcore.  Auto is fine if not overclocking
        
        CPU PLL…………………....1.500V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.5-1.65.  Auto is fine if not overclocking
        
        CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 
        
        CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly 
        
        [b]MCH/ICH[/b]
        MCH Core…………….....1.100V...........: << 
        MCH Reference….…….0.800V...........; <<< Leave
        MCH/DRAM Ref.…......0.900V...........: <<< Leave
        ICH I/O……………….....1.500V............: <<< Leave
        ICH Core…………...……1.100V............: <<< Leave
        
        [b]DRAM[/b]
        DRAM Voltage ……....1.800V............: 
        DRAM Termination .…0.900V............: <<< Leave
        Channel A Reference 0.900V............: <<< Leave
        Channel B Reference 0.900V............: <<< Leave
        
        [b][U]Advanced Settings[/U][/b][U][/U]
        Limit CPUID Max. to 3.....................: [Disabled]
        No-Execute Memory Protect............: [Enabled]
        CPU Enhanced Halt (C1E)................: [Disabled]
        C2/C2E State Support....................: [Disabled]
        x C4/C4E State Support..................: [Disabled]
        CPU Thermal Monitor 2(TM2) ...........: [Enabled]
        CPU EIST Function.........................: [Disabled]
        Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
        
        [b][U]Integrated Peripherals[/U][/b][U][/U]
        Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

        Comment


        • #5
          Re: GIGABYTE GA-EP45-UD3R Memory settings

          thanks for all the help but I have since retired the GA-EP45-UD3R, too many problems..at least for me. I may install it again later..no more rma

          Comment


          • #6
            Re: GIGABYTE GA-EP45-UD3R Memory settings

            I noticed that in your other thread. Why you give up so easy?

            Did you get another brand or board, or do you already have a main system?

            Comment


            • #7
              Re: GIGABYTE GA-EP45-UD3R Memory settings

              I had to get something up and running I could count on. The EP45-UD3R is in another case now running. Still no HDD LED, USB 2.0 front ports, and front audio. Just gonna use it to play with. Thats the best pic I can come up with right now. My call to gigabyte support was the final straw.
              Last edited by man00; 03-15-2009, 12:38 PM.

              Comment

              Working...
              X