Hello all. 1st post and new to overclocking. I built a new system for x-mas, had a few issues installing vista but that's worked out.
Specs.
Wolfdale e8500
Gigabyte ep45-ud3p
8 gigs G. Skill ddr2 1000 (pc2 8000) (4*2)
Artic Cooler freezer 7 pro
HIS 4870 1 gig gpu
Pc Power and Cooling silencer 610
in a Cooler Master HAF 932
The BIOS I set it with was
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Fast
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................:.0 [+.5 kicks it up to 3.8+]
CPU Frequency ...........................: 3.60
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 401
PCI Express Frequency (Mhz) .........: 100
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................: 900
CPU Clock Skew (ps)....................: 50
MCH Clock Skew (ps)...................: 100
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: 400
System Memory Multiplier ..............: 2.00
Memory Frequency (Mhz) ..............: 802
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................15
Advanced Timing Control
tRRD...........................................3
tWTR..........................................3
tWR............................................6
tRFC...........................................52
tRTP...........................................3
Command Rate (CMD) ....................:0
Driving Strength Profiles
Driving Strength ............................800
Channel A
Static tRead Value.........................:9
tRD Phase0 Adjustment...................:auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Channel B
Static tRead Value.........................:9
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................: 1.26250
CPU Termination…..... 1.200V*.......: 1.22
CPU PLL…………………....1.500V*.......: 1.5
CPU Referen.…………....0.755V*.......: .75
CPU Reference2………,,0.800V*.......: n/a
MCH/ICH
MCH Core…………….....1.100V...........: 1.2
MCH Reference….…….0.800V...........; auto
MCH/DRAM Ref.…......0.900V...........: auto
ICH I/O……………….....1.550V............: auto
ICH Core…………...……1.100V............: auto
DRAM
DRAM Voltage ……....1.800V............: 2.0
DRAM Termination .…0.900V............: auto
Channel A Reference 0.900V............: auto
Channel B Reference 0.900V............: auto
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
runs fine but there is an 8 degree differential in hw monitor between core0 and core1, core0 is running at 27c and core1 is at 35c. Any ideas, tips, tricks or suggestions? thank you
Specs.
Wolfdale e8500
Gigabyte ep45-ud3p
8 gigs G. Skill ddr2 1000 (pc2 8000) (4*2)
Artic Cooler freezer 7 pro
HIS 4870 1 gig gpu
Pc Power and Cooling silencer 610
in a Cooler Master HAF 932
The BIOS I set it with was
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Fast
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................:.0 [+.5 kicks it up to 3.8+]
CPU Frequency ...........................: 3.60
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 401
PCI Express Frequency (Mhz) .........: 100
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: 800
PCI Express Clock Drive.................: 900
CPU Clock Skew (ps)....................: 50
MCH Clock Skew (ps)...................: 100
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: 400
System Memory Multiplier ..............: 2.00
Memory Frequency (Mhz) ..............: 802
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................15
Advanced Timing Control
tRRD...........................................3
tWTR..........................................3
tWR............................................6
tRFC...........................................52
tRTP...........................................3
Command Rate (CMD) ....................:0
Driving Strength Profiles
Driving Strength ............................800
Channel A
Static tRead Value.........................:9
tRD Phase0 Adjustment...................:auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Channel B
Static tRead Value.........................:9
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................: 1.26250
CPU Termination…..... 1.200V*.......: 1.22
CPU PLL…………………....1.500V*.......: 1.5
CPU Referen.…………....0.755V*.......: .75
CPU Reference2………,,0.800V*.......: n/a
MCH/ICH
MCH Core…………….....1.100V...........: 1.2
MCH Reference….…….0.800V...........; auto
MCH/DRAM Ref.…......0.900V...........: auto
ICH I/O……………….....1.550V............: auto
ICH Core…………...……1.100V............: auto
DRAM
DRAM Voltage ……....1.800V............: 2.0
DRAM Termination .…0.900V............: auto
Channel A Reference 0.900V............: auto
Channel B Reference 0.900V............: auto
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
runs fine but there is an 8 degree differential in hw monitor between core0 and core1, core0 is running at 27c and core1 is at 35c. Any ideas, tips, tricks or suggestions? thank you
Comment