No announcement yet.

EP-45-DS3R Voltage question

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • EP-45-DS3R Voltage question

    Hi , I’m new to overclocking and could use some advice. After reading some of the posts here I have a setup that seems stable as listed below.
    <?xml:namespace prefix = o ns = "urn:schemas-microsoft-com:office:office" /><o:p></o:p>
    My main question is what to manually set the CPU PLL and CPU Term voltages at in the bios? I’ve got the Vcore manually set to 1.36250 in the bios, which CPUZ shows as 1.328 at idle and 1.296 when I run prime95’s ‘in place largeFFTs(max heat, power consumption)’ test.
    <o:p></o:p>
    Any advice about any settings or timings that would let me get more performance would be welcome
    <o:p></o:p>
    <o:p></o:p>
    Gigabyte EP-45-DS3R (F10 bios)
    Intel 2 Duo E8500
    OCZ Reaper HPC 4GB (4 x 1GB) DDR2 1150 (PC2 9200) Model OCZ2RPR11502GK <o:p></o:p>
    Rosewill RCX-Z775-EX cooler

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ..................: [Auto]
    CPU Clock Ratio ..............................: 9
    Fine CPU Clock Ratio.........................: [+0.5]
    CPU Frequency ...............................: 3.85Ghz (406 FSB x 9)


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control...................: [Enabled]
    CPU Host Frequency (Mhz) .............: [406]

    PCI Express Frequency (Mhz) ..........: [100]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: 800
    PCI Express Clock Drive.................: 900
    CPU Clock Skew ....................: 50
    MCH Clock Skew ....................: 150


    DRAM Performance Control
    Performance Enhance....................: [STANDARD]
    Extreme Memory Profile (X.M.P.)........: Disabled
    (G)MCH Frequency Latch.................: [400MHz]
    System Memory Multiplier ..............: [2.66D]
    Memory Frequency (Mhz) ................: 1083
    DRAM Timing Selectable ................: [Manual]

    Standard Timing Control
    CAS Latency Time..........................:5
    tRCD ...........................................:5
    tRP'.............................................: 5
    tRAS............................................:1 5

    Advanced Timing Control
    tRRD............................................:4 Auto
    tWTR.......................................... :4 Auto
    tWR.............................................:8 Auto
    tRFC............................................:5 6 Auto

    tRTP...........................................:4 Auto
    Command Rate (CMD) ....................:0 Auto

    Channel A & B match

    Channel A
    Static tRead Value.........................10
    tRD Phase0 Adjustment...................:Auto
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto
    Twr2wr(Different Rank)...................:Auto
    Twr2rd(Different Rank)...................:Auto
    Trd2wr(Same/Diff Rank)..................:Auto
    Dimm1 Clock Skew Control...............:Auto
    Dimm2 Clock Skew Control...............:Auto

    Driving Strength…………………Auto

    Motherboard Voltage Control
    Voltage Type.………... Manual
    CPU
    CPU Vcore….……….........................: 1.36250V CPUZ shows as 1.328 at idle and 1.296 when I run prime95’s ‘in place largeFFTs(max heat, power)’ test.

    CPU Termination…..... 1.200V......: Auto <-- What should this be manually changed to in relation to the vcore setting I’m using?

    CPU PLL…………………....1.500V …..:Auto <-- What should this be manually changed to in relation to the vcore setting I’m using?

    CPU Referen.…………....0.760V ………Auto

    MCH/ICH
    MCH Core…………….....1.240V
    MCH Reference….…….0.760V...........Auto
    MCH/DRAM Ref.…......0.900V...........Auto
    ICH I/O……………….....1.500V............Auto

    DRAM
    DRAM Voltage ……....1.800V............: 2.10v
    DRAM Termination .…0.900V............: Auto
    Channel A Reference 0.900V............: Auto
    Channel B Reference 0.900V............: Auto

    Advanced Settings
    Limit CPUID Max. to 3.....................: disabled
    No-Execute Memory Protect............:enabled
    CPU Enhanced Halt (C1E)................: disabled
    CPU Thermal Monitor 2(TM2) ...........: enabled
    CPU EIST Function.........................: disabled
    Virtualization Technology................: enabled <o:p></o:p>
    <o:p></o:p>
    <o:p></o:p>
    Thanks for any help
    Last edited by psob2; 12-20-2008, 04:17 PM. Reason: settings change
Working...
X