No announcement yet.

ga-x48-dq6 and ocz2rpr800c44gk ahhhhh

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • ga-x48-dq6 and ocz2rpr800c44gk ahhhhh

    Hi there folks, so glad i found this forum!!!

    I have having issues getting the above motherboard to work the 4gb ram...board works fine with one dimm in at a time!!!

    I have read loads of posts with settings for timings voltage etc but just cannot get it stable...

    these are the settings i have set at the moment:

    Memory timings:
    4:4:4:15
    2T

    Advanced timings:

    Act to Act tRRD 3
    Rank write to read delay 3
    write to pre charge deplay 6
    refresh to precharge deplay 56
    read to precharge deplay 3
    static tRead value 8
    static tRead phase adjust 0
    command rate 2

    i have also set the ram to 2.1v
    and upped the gmpc up by 0.2

    and its still unstable...

    so I am woundering if anyone else has any advice on what to try next or if anyone has the same board and ram would you be so kind as to post your ram settings ?!?

    think if i cannot get these to work might have to send them back and get another make of ram..

    Cheers for your time

    Rich

  • #2
    Re: ga-x48-dq6 and ocz2rpr800c44gk ahhhhh

    Please test each stick one at a time in slot one to be sure none are faulty >>>
    Memtest86+ - Advanced Memory Diagnostic Tool

    Run this test with manually set main timings, ram voltage set, and performance enhance set to standard. If both stick pass please do link me to your ram, let me know what CPU you have and what BIOS you are using and fill this out and I will advise back >>>

    This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

    Code:
    Robust Graphics Booster___________ [Auto]
    CPU Clock Ratio ____________ [8] 
    Fine Clock Ratio ____________[0.5]
    CPU Host Clock Control_ [Enabled]
    CPU Host Frequency (MHz)__________ [450] 
    PCI Express Frequency (Mhz)_______ [100]
    C.I.A. 2__________________________ [Disabled]
    System Memory Multiplier (SPD)____ [2.00]
    DRAM Timing Selectable_______ SPD __ [Manual]
    
    Performance Enhance = [Standard]
    
    CAS Latency Time________________ ?
    Dram RAS# to CAS# Delay_________ ?
    Dram RAS# Precharge Delay_______?
    Precharge Delay (tRAS)__________ ?
    
    ACT to ACT Delay (tRRD)_________ ?
    Rank Write to READ Delay________ ?
    Write to Precharge Delay_________ ?
    Refresh to ACT Delay______________ ?
    Read to Precharge Delay__________ ?
    Static tRead Value_______________
    Static tRead Phase Adjust________ [Auto]
    
    CPU/PCIEX Clock Driving Control [800mV]
    CPU Clock Skew Control [normal]
    GMCH Clock Skew Control [Normal]
    
    System Voltage Control____ [Manual]
    DDR2 OverVoltage Control__ [+0.300V] 
    PCI-E OverVoltage Control_ [+0.1V] 
    FSB OverVoltage Control___ [+0.1V] 
    (G)MCH OverVoltage Control [+0.1V] 
    CPU Voltage Control_______ [1.25]
    
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
    
    Integrated Peripherals
    Legacy USB Storage Detect___________________[Disabled] *Note* Must be enabled to flash from USB

    Comment

    Working...
    X