No announcement yet.

EP43-DS3 BIOS OC help?

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • EP43-DS3 BIOS OC help?

    Hi can somebody hellp me oc my pc?

    what ever i do its not good.

    my pc:
    Intel e8400
    EP45-DS3 F9 bios
    G.Skill PK series 2x2 gb ddr2 800
    XFX 9800GTX+
    Samsung f1 500gb
    Corsair 400W

    here is cpu-z and gpu-z:


    Thnx. and sorry for my bad eng
    Last edited by ToWaRR; 12-10-2008, 07:54 AM. Reason: I edit my mbo

  • #2
    Re: EP43-DS3 BIOS OC help?

    What settings are you using now, and what would you like to run your CPU at and I will advise back. For now, you do need to disable C1E and EIST For sure if you are wanting to overclock >>>

    This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

    Code:
    [b][u]MB Intelligent Tweaker(M.I.T.)[/u][/b]
    Robust Graphics Booster ...............: 
    CPU Clock Ratio ..........................: 
    Fine CPU Clock Ratio.....................:.0
    CPU Frequency ...........................: 
    
    
    [b][u]Clock Chip Control [/u][/b]
    [b][u]Standard Clock Control[/u][/b]
    CPU Host Clock Control..................: [Enabled] 
    CPU Host Frequency (Mhz) ............: Mhz
    [B]PCI Express Frequency (Mhz) .........:Set to 100[/B]
    
    C.I.A.2 .................................:[Disabled]
    
    
    [b][u]Advanced Clock Control [Press Enter][/u][/b]
    CPU Clock Drive...........................: <<< 
    PCI Express Clock Drive.................: <<< 
    CPU Clock Skew (ps)....................: <<< 
    MCH Clock Skew (ps)...................: <<< 
    
    
    [b][u]DRAM Performance Control[/u][/b][u][/u]
    [B]Performance Enhance...................: [STANDARD][/B]
    Extreme Memory Profile (X.M.P.).....: Disabled
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: 
    Memory Frequency (Mhz) ..............: 
    DRAM Timing Selectable ................: [Manual]
    
    [b]Standard Timing Control[/b]
    CAS Latency Time........................
    tRCD .........................................
    tRP'...........................................
    tRAS..........................................
    
    [b][u]Advanced Timing Control[/u][/b]
    tRRD...........................................
    tWTR..........................................
    tWR............................................
    tRFC...........................................
    tRTP...........................................
    Command Rate (CMD) ....................:2
    
    [u][b]Driving Strength Profiles[/b][/u][b][/b]
    Driving Strength ............................
    
    [b]Channel A[/b]
    Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
     tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    
    [b]Channel B[/b]
    Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
     tRD Phase0 Adjustment...................:<<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
     tRD Phase2 Adjustment .................:Auto
     tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 
    Twr2wr(Different Rank)...................:Auto 
    Twr2rd(Different Rank)...................:Auto 
    Trd2wr(Same/Diff Rank)..................:Auto 
    Dimm1 Clock Skew Control...............:Auto  ps
    Dimm2 Clock Skew Control...............:Auto  ps
    
    [b][U]Motherboard Voltage Control[/U][/b][U][/U]
    Voltage Type.………... Manual
    [b]CPU[/b]
    CPU Vcore….……….........................:
    CPU Termination…..... 1.200V*.......: <<< Leave
    CPU PLL…………………....1.500V*.......: << Please set to stock, Auto overvolts this way to much
    
    CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 
    
    CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly 
    
    [b]MCH/ICH[/b]
    MCH Core…………….....1.100V...........: << 
    MCH Reference….…….0.800V...........; <<< Leave
    MCH/DRAM Ref.…......0.900V...........: <<< Leave
    ICH I/O……………….....1.550V............: <<< Leave
    ICH Core…………...……1.100V............: <<< Leave
    
    [b]DRAM[/b]
    DRAM Voltage ……....1.800V............: 
    DRAM Termination .…0.900V............: <<< Leave
    Channel A Reference 0.900V............: <<< Leave
    Channel B Reference 0.900V............: <<< Leave
    
    [b][U]Advanced Settings[/U][/b][U][/U]
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Disabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Disabled]
    Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
    
    [b][U]Integrated Peripherals[/U][/b][U][/U]
    Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

    Comment

    Working...
    X