GIGABYTE Latest Beta BIOS

[patrykdzadz]

When can we expect a full F31 release for the X570 boards stasio ?

[mgfirewater]

UPDATE: I was able to run 3933cl16 stable using mixed RAM kits (Micron Rev E and Hynix CJR) with 1967 FCLK. No crashes No BSOD No sound distortion, just usb 2.0 headers are bugged. Find the timings below,



Games are more consistent in FPS now and I'm definitely seeing improvements in the 0.1 and 1% low FPS. I think we can recommend dual rank sticks over single rank now.

your zentiming screen says you use f11j, so its clear why the usb hub is stuttering. since 11k it is fix on my b550 aorus pro.

[DethSpade]

AMD 5900x
Ram: 4600MHZ Trident Z RGB F4-4600C18-8GTZR
x570 Aorus Xtreme Rev 1.0
Bios: F31n

Ended up switching my ram to slots A2 and B2. I found this in the manual: For optimum performance, when enabling Dual Channel mode with two memory modules, we recommend that you install them in the DDR4_A2 and DDR4_B2 sockets. After doing so, im noticing my RAM is a lot more stable. (Could not get over 3200mhz before)

Successfully posted with 3800MHZ


Been using this for almost 24 hours and is extremely stable. With others reporting in that higher clocks are not stable, im waiting till the next revision to go even higher ;)

[Jason_Cruze]

your zentiming screen says you use f11j, so its clear why the usb hub is stuttering. since 11k it is fix on my b550 aorus pro.

F11k FCLK OC support is very bad and requires major tweaks for even 1900FCLK, whereas on default settings just increasing the FCLK to 1967 on f11j runs stable. So yeah I prefer f11j over f11k and also those USB problems can be omitted by disabling GCM.

[Jason_Cruze]

AMD 5900x
Ram: 4600MHZ Trident Z RGB F4-4600C18-8GTZR
x570 Aorus Xtreme Rev 1.0
Bios: F31n

Ended up switching my ram to slots A2 and B2. I found this in the manual: For optimum performance, when enabling Dual Channel mode with two memory modules, we recommend that you install them in the DDR4_A2 and DDR4_B2 sockets. After doing so, im noticing my RAM is a lot more stable. (Could not get over 3200mhz before)

Successfully posted with 3800MHZ


Been using this for almost 24 hours and is extremely stable. With others reporting in that higher clocks are not stable, im waiting till the next revision to go even higher ;)

I just populated the RAM sets in each individual channel CJR on one channel Micron Rev E on other channel.

[Geicher]

Hi,

another update from me: Since yesterday no more crashes / WHEA so far. However I'm no unable to get FCLK higher than 1800 MHz. But at least the system seems to run stable for now.

[Wechhe]

Hi,

another update from me: Since yesterday no more crashes / WHEA so far. However I'm no unable to get FCLK higher than 1800 MHz. But at least the system seems to run stable for now.

Which Board, UEFI Version, CPU (+settings) and RAM(+settings) are you using again?

[Geicher]

Hey,

I'm now using F31n, 5600X stock, and 2x 8 GB G.Skill Ripjaws @3200MHz.

[Jesdga95]

New to the forum. 5950x + Aorus X570i and 3600 MHz RAM

Bios version F31J seems to be stable, L version wouldn't let me go above 3200 MHz without BSODs and restarts. However I'm still unable to run my CPU with PBO enabled (instant reboot when running any kind of heavy load) and I'm getting low cinebench scores (9500ish). I'm also seeing that one CCD is MUCH hotter than the other one (by like 15+ degrees) at times, mostly on games. Temps are very close on both CCDs when running benchmarks. Already re-applied thermal paste and it didn't seem to help:

[DethSpade]

Jesdga95 what cooler do you have?

[Jesdga95]

Jesdga95 what cooler do you have?

NZXT X53, I ran the pump on liquid temps and full speed, still seeing the same issue

[bovcan]

well, F32n is another story. on F32l vcore in bios didnt have effect, now it does BUT on F32l I could run 101mhz, 102mhz bus clock, now I cant run at even 101MHZ. I just get BDOS before enetering Windows.
HWinfo still show 99MhZ bus clock with SVM enable...

[nate37]

https://www.youtube.com/watch?v=eCQg0OgpPRA

(The computer turns off in about 3 :11 )

I don't know if it's getting worse or not.
Now it turns off intermittently when I watch YouTube or Twitch.

1. Bios F10, F11g, F11k, F11m versions all have the same symptoms
2. Overclocking? (ram overclock? , PBO?)
3. Initialization status of bios settings
4. Power A/S Check Results OK
5. CPU, Graphic Card Bench Results OK

CPU : Ryzen 5600X
MB : GIGABYTE B550M AORUS PRO-P
VGA: GAMING GeForce RTX 3080 Trinity D6X 10GB
Power: Sysonic FOCUS GOLD GM-850 Modular
RAM: Samsung DDR4-3200 (16GB) X 2
SSD: Samsung PM981a M.2 NVMe
COOLER: NZXT KRAKEN X63
Case: 3RSYS L530
Monitor: LG 27GL850

[nate37]

I didn`t use ram overclock and PBO

[olpol]

New to the forum. 5950x + Aorus X570i and 3600 MHz RAM

Bios version F31J seems to be stable, L version wouldn't let me go above 3200 MHz without BSODs and restarts. However I'm still unable to run my CPU with PBO enabled (instant reboot when running any kind of heavy load) and I'm getting low cinebench scores (9500ish). I'm also seeing that one CCD is MUCH hotter than the other one (by like 15+ degrees) at times, mostly on games. Temps are very close on both CCDs when running benchmarks. Already re-applied thermal paste and it didn't seem to help:

CCD difference in games same to me with 5900X, seems normal behaviour....