EP45-DS3R Temperature

[arctia]

Hey, I just got my 2x2GB G.skill sticks. Was forced to raise the MCH voltage to 1.3 or else I kept getting blue screens in games. Now I'm seeing 50 degrees on this "System" temperature. My question is what is that temperature a measure of? And is it safe?

[mxcrowe]

Re: EP45-DS3R Temperature

What are you using to measure temps? Are you talking about idle temps? There are 3 primary temperature readings from the motherboard. First, from the cores themselves, then 2 from the board. We were discussing this on another thread...I believe one sensor is near the northbridge and the other near the cpu socket. I'm assuming "system" is the northbridge sensor. My runs at 41C idle - essentially constant. In any case, a constant temp of 50C seems high, but could depend on how you have the whole system overclocked. What are your settings, other than the MCH Core?

[Lsdmeasap]

Re: EP45-DS3R Temperature

It is the Northbridge Temp. Did you try 1.2 or 1.25?

Yes, it is safe as long as you are under 65-70. What settings are you using? You may have had things set to tight is why you felt you needed 1.3, but maybe not. So just wondering so I could advise better

You could add a 40MM fan on the NB heatsink, or at least redo the thermal paste under there if you feel up to it. If you do, use NON conductive paste

Want to give me what you are using in the MIT, and I will see if I see anything that may have stopped you from using less MCH >>>>

This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............:
CPU Clock Ratio ..........................:
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................:


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: Mhz
PCI Express Frequency (Mhz) .........:Set to 100


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<<
PCI Express Clock Drive.................: <<<
CPU Clock Skew (ps)....................: <<<
MCH Clock Skew (ps)...................: <<<


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............:
Memory Frequency (Mhz) ..............:
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................
tRCD .........................................
tRP'...........................................
tRAS..........................................

Advanced Timing Control
tRRD...........................................
tWTR..........................................
tWR............................................
tRFC...........................................
tRTP...........................................
Command Rate (CMD) ....................:2

Channel A
Static tRead Value.........................:7-10
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Channel B
Static tRead Value.........................:7-10
tRD Phase0 Adjustment...................:<<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................:
CPU Termination…..... 1.200V*.......: <<< Leave
CPU PLL…………………....1.500V*.......: <<< Leave
CPU Referen.…………....0.755V*.......: <<< Leave
CPU Reference2………,,0.800V*.......:<<< Leave

MCH/ICH
MCH Core…………….....1.100V...........: <<
MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.550V............: <<< Leave
ICH Core…………...……1.100V............: <<< Leave

DRAM
DRAM Voltage ……....1.800V............:
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]