If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
No announcement yet.
Gigabyte X38/P35/P965 (DS* DQ* S3) Overclocking and General BIOS tweaking Guide
You need to set System Memory Multiplier manually to 2.40B otherwise the memory will run as DDR-1000 and may not be up to the task with relatively low voltage even with the looser timings.
Please understand that it will be easier to assist you in a new thread, and the detail in your signature are also essential.
hmm ok when i overclock my memory than with 2.00 multiplier
Re: Gigabyte X38/P35/P965 (DS* DQ* S3) Overclocking and General BIOS tweaking Guide
While overclocking, leave on 100 is the usual advice, otherwise it will just be another complication. Play with pci after cpu/ram overclock is complete if u want.
If u saw this in a template, it is not a recommended setting, but a leftover from an individual overclock.
CPU =i7 950 - DO stepping - Batch #3014A844 Cooling = EK HF Full Nickel - XSPC RX360 - Laing DDC 18W - XSPC Bay Reservoir Motherboard = GA-X58A-UD3R Revision 2, BIOS Version = Award FC Ram = 3x2gig Corsair TR3X6G1600C8D G Video = 2 X Palit GTX460 Sonic Platinum 1GB OC sli Monitor = 22" LG Flatron W2242T 1680 x 1050 Case = Coolermaster CM690 PSU = Corsair HX850 OS = Windows 7 Professional x64
While overclocking, leave on 100 is the usual advice, otherwise it will just be another complication. Play with pci after cpu/ram overclock is complete if u want.
If u saw this in a template, it is not a recommended setting, but a leftover from an individual overclock.
Re: Gigabyte X38/P35/P965 (DS* DQ* S3) Overclocking and General BIOS tweaking Guide
Yep. Very similar bios. There are plenty of EP45 posts in the forum too.
CPU =i7 950 - DO stepping - Batch #3014A844 Cooling = EK HF Full Nickel - XSPC RX360 - Laing DDC 18W - XSPC Bay Reservoir Motherboard = GA-X58A-UD3R Revision 2, BIOS Version = Award FC Ram = 3x2gig Corsair TR3X6G1600C8D G Video = 2 X Palit GTX460 Sonic Platinum 1GB OC sli Monitor = 22" LG Flatron W2242T 1680 x 1050 Case = Coolermaster CM690 PSU = Corsair HX850 OS = Windows 7 Professional x64
Re: Gigabyte X38/P35/P965 (DS* DQ* S3) Overclocking and General BIOS tweaking Guide
Hello ,
I'm trying to OC my E8400 on this P45 UD3R motherboard.
I just played with the voltages and ran OCCT for 20 minutes, but I don't know if they're set correctly. Which should I lower and which should I raise?
I'm trying to OC my E8400 on this P45 UD3R motherboard.
I just played with the voltages and ran OCCT for 20 minutes, but I don't know if they're set correctly. Which should I lower and which should I raise?
Could you guys help me please?
You are the only one that can tell really. All look within reason. If they are stable than they are just fine.
What is memory max voltage specs?
20 minutes OCCT are not enough, run 8+ hours medium data set to be more sure.
IBT(IntelBurnTest) may help indicate if there's enough Vcore and/or if it can be lowered.
Would be better if you make your own thread, post screen capture of MemSet main(click >>) and SPD(click spd) windows.
Add this system spec to your signature including link to ram specs or at least model/part number.
Re: Gigabyte X38/P35/P965 (DS* DQ* S3) Overclocking and General BIOS tweaking Guide
Continued from page 17...
Hi I took some time off, those late nights along with BSOD's & other instability issues drove me mad so I took a breather.
Anyway back now so I probably should start where I left off. With my current setting I finally got my baby to work, only this time did what
Salty suggested, or just say I detoxed myself from that A2.5 divider that I was hooked on. Good news it worked without the need of more juice to the CPU.
As it turned out or I realized I should say it was that divider keeping me back, the CPU itself is well capable of 4Ghz & reasonably
cool with temps of: As according to CoreTemp Idle @38~41 Load @60~62.
Speed Fan shows exactly the same as Real Temp idle @ 44~47 Load @62~65, Overall OC boost: CPU +34.6% _ FSB +27.6%
Salty thanks for all your help, Lsdmeasap superb tutorial without it I'd be still on 3.0Ghz thanks a lot.
Now here are my final settings
Robust Graphics Booster___________ [Auto]
CPU Clock Ratio ____________ [9]
Fine Clock Ratio ____________[0.5]
CPU Host Clock Control_ [Enabled]
CPU Host Frequency (MHz)__________ [425]
PCI Express Frequency (Mhz)_______ [101]
C.I.A. 2__________________________ [Disabled]
Performance Enhance = [Standard]
System Memory Multiplier (SPD)____ [2.40B]
DRAM Timing Selectable_______ SPD __ [Manual]
CAS Latency Time________________ 5
Dram RAS# to CAS# Delay_________ 5
Dram RAS# Precharge Delay_______5
Precharge Delay (tRAS)__________18
ACT to ACT Delay (tRRD)_________3 auto
Rank Write to READ Delay________ 6 auto
Write to Precharge Delay_________ 46 auto
Refresh to ACT Delay______________3 auto
Read to Precharge Delay__________5 auto
Static tRead Value_______________1 auto
Static tRead Phase Adjust________1 [Auto]
Command Rate (CMD)_______________2 auto
CPU/PCIEX Clock Driving Control [800mV]
CPU Clock Skew Control [normal]
GMCH Clock Skew Control [Normal]
System Voltage Control____ [Manual]
DDR2 OverVoltage Control__ [+0.300V]
PCI-E OverVoltage Control_ [+0.1V]
FSB OverVoltage Control___ [+0.1V]
(G)MCH OverVoltage Control [+0.2V]
CPU Voltage Control_______ [1.51250]
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC
Integrated Peripherals
Legacy USB Storage Detect___________________[Disabled] *Note* Must be enabled to flash from USB
Re: Gigabyte X38/P35/P965 (DS* DQ* S3) Overclocking and General BIOS tweaking Guide
Good one. You stuck with it. Nice to hear I may have managed to help too.
The cpu volts would be high for my E8500, but if you have temps under control ... 4.037GHz, quite good for a QX9650 as far as I kno. I'm guessing it's not hot where u compute at.
My only thoughts;
Static tRead Value : Rather than auto around 7 is good. I would suggest 7. You're after lowest number that yr PC boots stably on. Auto sets this too high/slow. Memset can show u what auto sets it to under "performance level". Only a small boost but looks good in Everest memory bench tool.
Static tRead Phase Adjust : as far as I know, best left on auto.
Loadline Calibration: Disputed setting. Up to the individual. If you have it auto or disabled with yr cpu volts shown, then enabling might allow use of lower nominal vcore. Not sure if that affects temps.
Keep on clockin'
CPU =i7 950 - DO stepping - Batch #3014A844 Cooling = EK HF Full Nickel - XSPC RX360 - Laing DDC 18W - XSPC Bay Reservoir Motherboard = GA-X58A-UD3R Revision 2, BIOS Version = Award FC Ram = 3x2gig Corsair TR3X6G1600C8D G Video = 2 X Palit GTX460 Sonic Platinum 1GB OC sli Monitor = 22" LG Flatron W2242T 1680 x 1050 Case = Coolermaster CM690 PSU = Corsair HX850 OS = Windows 7 Professional x64
Re: Gigabyte X38/P35/P965 (DS* DQ* S3) Overclocking and General BIOS tweaking Guide
Hi Everyone,
I am having difficulties with my new Corsair Dominator 1066 rams I got random restarts.
I have
P35-DQ6 Rev:1.0 F9
Q6600 with Noctua Cooling
Corsair Dominator 2x2 1066 Mhz Modules
Ati x1950 xtx
320 x 2 Raid 0
2 x 1 TB Sata II
X-FI Elite Pro
Robust Graphics Booster___________ [Auto]
CPU Clock Ratio ____________ [9X ]
CPU Frequency _____________ [2.4 (266X9)]
CPU Host Clock Control_ [Enabled]
CPU Host Frequency (MHz)__________ [266]
PCI Express Frequency (Mhz)_______ [100]
C.I.A. 2__________________________ [Disabled]
System Memory Multiplier (SPD)____ [2.00] Auto
Memory Frequency _______________[1066]
DRAM Timing Selectable_______ SPD __ [Manual]
Performance Enhance = [Standard]
CAS Latency Time________________(7) 5
Dram RAS# to CAS# Delay_________(7) 5
Dram RAS# Precharge Delay_______(7) 5
Precharge Delay (tRAS)__________ (24) 18
ACT to ACT Delay (tRRD)_________ 4 (Auto)
Rank Write to READ Delay________ 4 (Auto)
Write to Precharge Delay_________ 8 (Auto)
Refresh to ACT Delay______________ 68 (Auto)
Read to Precharge Delay__________ 4 (Auto)
Static tRead Value_______________ 7 (Auto)
Static tRead Phase Adjust________ [Auto]
System Voltage Control____ [Manual]
DDR2 OverVoltage Control__ [+0.300V]
PCI-E OverVoltage Control__ [+0.0v]
FSB OverVoltage Control___ [+0.0V]
(G)MCH OverVoltage Control [+0.0V]
CPU Voltage Control_______ [1.3]
Normal CPU Vcore _________ [1.3000v]
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
Comment